Storage; Disposal And Recycling - Scheppach MFH380-20Li Dual Original Anleitungen

Immediately replace damaged or blunt cutting tools,
even in the event of minor damage.
The user is responsible for all damages caused
by non-compliance with instructions in this man-
ual. This also applies to non-authorized modifi-
cations of the tool, use of non-authorized spare
parts, accessories, working tools, unrelated and
not intended use, secondary damages due to use
of faulty components.
Wear Parts
Even when used in the intended way, some compo-
nents are subject to normal wear. They have to be
replaced depending on the kind of duration of usage.
These parts include, among others, the cutting tool and
the retaining disk.
m Warning!
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause poor performance, possible injury and may
void your warranty.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement
parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1.4 7910700702
Transport guard for blade 3 teeth 3904801065
Blade with 4 teeth Ø 255 x 1.4 7910700705
Transport guard for blade 4 teeth 3904801066
Blade with 8 teeth Ø 255 x 1.4 7910700711
Transport guard for blade 8 teeth 3904801066
Pole pruner:
Saw chain Oregon 91P033X
Guide rail Oregon 080SDEA318 7912400701
Transport guard for chain
Hedge trimmer:
Blade for hedge trimmer 395 mm 7910700720
Transport guard for blade
40 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
7910700719
7910100715
3904801039
3904801043
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma-
bles.
Wear parts*: Carbon brush, line spool, cutting blade,
saw chain, guide rail
* Not necessarily included in the scope of delivery!
11.

Storage

Cleaning
• Keep handles free of oil, so you always have a secure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Never immerse the equipment in water or other liquids
in order to clean it.
Storage
Note: Store the equipment in a dry place and far away
from possible ignition sources such as an oven, a gas-fi
red hot water boiler, a gas-fi red dryer, etc.
Transport
Always attach the transport guard to all cutting tools. Fig.
1 (14a, 15a, 17a)
In order to prevent damage and injury, secure the tool
against tipping over and sliding when transporting it in
vehicles.
12.

Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in this
packaging can be reused or recycled.
The equipment and its accessories are made of various
types of material, such as metal and plastic. Defective
components must be disposed of as special waste. Ask
your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical
and electronic equipment (WEEE). This product must
be disposed of at a designated collection point. This
can occur, for example, by handing it in at an author-
ised collecting point for the recycling of waste elec-
trical and electronic equipment. Improper handling
of waste equipment may have negative consequenc-
es for the environment and human health due to po-