16_Changing The Battery; 17_Packaging; 18_Copyright; 19_Product Modifications - Elite TURNO Anleitung

EN
sensor as follows:
1) Open up the Turno housing (Pic. 1M) and remove the
sensor.
2) Slide the sensor cover sideways to open it. Place the
battery in the appropriate housing (Pic. 2M) and press the
button close to the battery holder once. Wait for the led
light to light up and repeat the operation until the led light
blinks 15 times (Pic. 3M). 15 blinks indicate that the sensor
has been properly paired with the hometrainer.
3) Place the sensor back inside the Turno housing (Pic.
4M).
WARNING: The side of the sensor with the 2 notches must
be facing the front side.
4) Replace the battery cover (Pic. 5M)
5) Check the circumference value set on app / device.
Verify the paragraph "Training" for right set-up.
ATTENTION!
An incorrect blinks value leads to incorrect power data.
An incorrect wheel circumference value leads to incorrect
speed data.
The display (app / cycle computer) does not connect
to the sensor:
Make sure the pairing process with the display has been
properly conducted and start pedalling.
Make sure you pedal on the hometrainer to awaken the
system before connecting the display.
Please verify that the battery is charged.
The display reads more than one sensor:
This indicates that two or more sensors are close enough to
be read. Try turning off or removing unnecessary sensors
and repeat the search process.
NOTES
When placed close to a TV, radio or electric motor,
interference can occur that may alter the correct
transmission of data. Avoid using the device within a
1.5-meter radius of other electronic equipment.
Do not use with other wireless devices, which can alter
correct data transmission.

16_CHANGING THE BATTERY

- Open up the hometrainer housing and remove the sensor
(Pic. 1M)
- Slide the sensor cover sideways to open it (Pic. 2M).
- Remove the old battery and replace with a new one with
the positive terminal facing upwards (Pic. 6M).
- Place the sensor back inside the Turno housing (Pic. 4M).
WARNING: The side of the sensor with the 2 notches
should be positioned upwards the front.
- Replace the battery cover (Pic. 5M)
- Keep the battery away from children. Immediately consult
a physician should the battery be swallowed.
ATTENTION:
44
- Put old batteries in the special
containers
- Do not disperse in the environment
- If the battery is replaced with one of the wrong type there
will be risk of explosion
USE & STORAGE CONDITIONS
The Misuro B+ sensor, like any other electronic device,
needs to be handled carefully. It must not be used in a
wet and/or damp environment. When not in use, it must be
stored in a cool and dry place. Please remove the battery if
you will not be using the device for a long period of time.Do
not expose the device to direct sunlight for a long period of
time. Operating temperature: min -20°C, max 50°C.

17_PACKAGING

If the roller needs to be shipped, careful packaging is
critical:
- pack up the Turno in its original box.
Concerning shipments, packages often undergo strong
shocks and bumps, so any non-original packaging might
irreparably damage the home trainer. Such damages are not
covered by the warranty.
Note: before shipping the home trainer or any of its
components to customer service, constult Elite or its
distributor or your own retailer.
Any non-planned shipment might not be accepted.

18_COPYRIGHT

No part of this manual may be reproduced or transmitted
without the written authorization of Elite S.r.l.
The Elite Turno software and relative code are property of
Elite S.r.l.

19_PRODUCT MODIFICATIONS

Also in view of any technical update, ELITE reserves
the right to make changes to the products or their
specifications without being obliged to notify or inform the
Customer beforehand for:
a) changes that do not affect negatively the product
performance;
b) changes required to meet or improve the product
specifications;
c) changes necessary for the products to comply with the
applicable legal requirements.
ELITE also reserves the right to supply these products
with these improvements without being obliged to or
responsible for applying the same modifications to any
previously purchased products, reserving also the right to
change prices and model availability according to market
conditions, component availability and other corporate