Name And List Of Components; Caution; Assembling Your Turbo Muin; Installing The Cassette On Turbo Muin - Elite turbomuin Bedienungsanleitung

Your Turbo Muin electronic trainer is made of the following components:
TURBO MUIN BODY
FRONT LEG TUBE
REAR LEG TUBE
M6 SAFETY SCREW
TRIANGLE ADAPTER
M8 LEG FIXING SCREW
* Quick release lever not supplied with this product.

CAUTION!

Turbo Muin is equipped with a freehub body com-
patible with 9/10/11-speed cassettes by Shimano
/ SRAM or by other manufacturers that use the
®
Shimano Standard.
®
An accessory freehub body compatible with Cam-
pagnolo 9/10/11 speed cassettes is available to re-
®
place the original Shimano compatible body provi-
ded on Turbo Muin; body replacement instructions
can be found on page 15.
Turbo Muin is compatible with 130 or 135 mm hubs
and 5mm diameter quick-release.
If you are unsure about the type of derailleur on
your bicycle, refer to the bicycle documentation
or contact your dealer to ensure compatibility with
Turbo Muin.

ASSEMBLING YOUR TURBO MUIN

CAUTION: the body of Turbo Muin is heavy, handle
with care and be sure to support it properly while
assembling the legs. It is recommended that this
operation be performed on a flat rugged surface,
such as a table.
CAUTION: before assembly, make sure you have all
the parts listed above and illustrated below.
• Position your Turbo Muin body (A) with the pla-
stic cover facing upward; open the front leg (Fig. 1)
tighten the M6 safety screw and lock washer (D + E)
with the correct torque of 3Nm /26.5 in-lbs (Fig. 2).
• Fix the front leg tube (B) with a 120 mm distance

NAME AND LIST OF COMPONENTS

1 Ref. A
1 Ref. B
1 Ref. C
1 Ref. D
1 Ref. F
4 Ref. G
®
M8 LEG FIXING NUT
M8 NUT COVER
FREEHUB BODY SPACERS
M6 LOCK WASHER
HEX WRENCH
(4.8 in) between the Ø8.5 (0.3 in) holes, using the
provided screws (G + H) (Fig. 3).
CAUTION: confirm that the direction of leg instal-
lation is correct; the longer end of the leg should
be positioned on the same side as the plastic cover.
CAUTION: the screw heads should be towards the
floor upon final assembly.
• Fix the rear leg tube (C), with a 140 mm distance
(5.5 in), between the Ø8.5 (0.3 in) holes, using the
provided screws (G + H) (Fig. 4).
CAUTION: confirm that the direction of leg instal-
lation is correct; the longer end of the leg should
be positioned on the same side as the plastic cover.
CAUTION: the screw heads should be towards the
floor upon final assembly.
• Place Turbo Muin on a flat surface, always ma-
king sure to handle it with care (Fig. 5).
• Place the four M8 nut covers (I) over the M8 nuts
(H) (Fig. 6 and Fig. 7).
INSTALLING THE CASSETTE
ON TURBO MUIN
• Fit the cassette onto the freehub body aligning the
spline patterns. See below for specific instructions
for different cassettes.
• If are installing a 9/10-speed cassette by Shima-
no / SRAM or by other manufacturers that use
® ®
the Shimano Standard, place the spacers (L) onto
®
the freehub body before fitting the cassette (Fig. 8).
• If you are installing an 11-speed cassette by Shi-
mano
/ SRAM or by other manufacturers that use
® ®
EN
4 Ref. H
4 Ref. I
2 Ref. L
1 Ref. E
15