Scheppach MFH5200-4P Originalbetriebsanleitung Seite 49

Add the 2-stroke oil in accordance with the fuel mixture
table.
Fuel
1 litre
2 litres
5 litres
9.2.2 Filling up fuel/oil mixture
Fuel and 2-stroke oil
Special 2-stroke oil for air-cooled 2-stroke engines with a
mixing ratio of 40:1 must be used.
WARNING
Do not use fuel that has not been correctly mixed with
2-stroke oil. This may cause permanent engine damage
and will void the manufacturer's warranty on this prod-
uct. Never use a fuel mixture that has been stored for
more than 90 days.
Note:
Clean the funnel before reusing it.
1. Mix the correct amount of petrol and 2-stroke oil in an
oil-petrol mixing bottle (44).
2. Clean the area around the filler opening.
Contamination in the fuel tank (10) will cause malfunc-
tions.
3. Carefully open the fuel filler cap (9) to release any ex-
cess pressure.
The fuel filler cap (9) is connected to an anti-loss de-
vice in the fuel tank (10) and cannot fall off.
4. Shake the oil-petrol mixture bottle (44) with the fuel
mixture again before filling it into the fuel tank (10).
5. Fill the fuel tank (10) with fuel using a funnel.
Observe the maximum filling quantity of 1 litre. Care-
fully fill the fuel up to the lower edge of the filler neck.
6. Close the tank cover (9) again. Ensure that the fuel
filler cap (9) is tightly sealed.
7. Clean the tank cover (9), fuel tank (10) and the sur-
roundings.
9.3 Fitting the front tubular shaft
(14/18/26) onto the tubular shaft
(12) (Fig. 1, 10)
ATTENTION
Never operate the product without an insert tool!
1. Remove the protective cap (14b/18b/26b) from the se-
lected front tubular shaft (14/18/26).
2. Remove the protective plugs (12a) from the tube shaft
(12) and loosen the star grip (13).
3. Push the selected front tubular shaft (14/18/26) onto
the tubular shaft (12).
Make sure that the locking pin (14a/18a/26a) on the
front tubular shaft (14/18/26) is aligned with the hole
on the tubular shaft (12).
4. Fix the front tubular shaft (14/18/26) to the tubular
shaft (12) using the star grip (13).
2-stroke engine oil (1:40)
0.025 litres
0.050 litres
0.125 litres
www.scheppach.com
9.4 Fitting the tubular shaft extension
(24) onto the tubular shaft (12)
(Figs. 1, 10)
ATTENTION
Do not use the tubular shaft extension with a
brush cutter/lawn trimmer!
• In order to carry out work at height, the pole-mounted
pruner or hedge trimmer can be used in combination
with the extension attachment (24).
• Fit the tubular shaft extension (24) between the tubu-
lar shaft (12) and a selected front tubular shaft
(18/26).
1. Remove the protective cap (24b) from the tube shaft
extension (24).
2. Remove the protective plug (12a) from the tubular
shaft (12) and separately loosen the star grip (13).
3. Push the tubular shaft extension (24) onto the tubular
shaft (12).
Make sure that the locking pin (24a) on the tubular
shaft extension (24) is aligned with the hole on the tu-
bular shaft (12).
4. Fix the tubular shaft extension (24) to the tubular shaft
(12) using the star grip (13).
5. Fit the pole-mounted pruner or hedge trimmer on the
tubular shaft extension (24) as described in 9.4.1.
9.4.1 Fitting the front tubular shaft (18/26)
on the tubular shaft extension (24)
ATTENTION
Never operate the product without an insert tool!
1. Remove the protective cap (18b/26b) from the select-
ed front tubular shaft (18/26).
2. Remove the protective plugs (24c) from the tube shaft
extension (24) and separately loosen the star grip
(25).
3. Push the selected front tubular shaft (18/26) onto the
tubular shaft extension (24).
Make sure that the locking pin (18a/26a) on the front
tubular shaft (18/26) is aligned with the hole on the tu-
bular shaft extension (24).
4. Fix the front tubular shaft (18/26) to the tubular shaft
extension (24) using the star grip (25).
9.5 Attaching the shoulder strap (43)
(Fig. 11-13)
CAUTION
Put on the shoulder strap, fit the desired insert tool and
adjust the product according to your needs. Ensure that
the product is properly in the prescribed working posi-
tion before starting the motor.
Notes:
The product may only be used with the carrying strap.
First, balance the product when the tool is switched off.
1. Put on the carrying strap (43).
GB | 49