Before Commissioning - Scheppach Tmr452-98C-Rd Originalbetriebsanleitung

Use a size 8/10 mm open-ended spanner (30) and
a size 10/13 mm open-ended spanner (30a).
3. Repeat the process on the other side.
9.6 ) L WWLQJWKHGULYHU¶ V VHDW) L J
1. Place one of the enclosed washers (1b) on the
shaft (1a) and insert the shaft (1a) through both
the mounting holes on the product frame and the
mounting holes on the driver's seat (1).
2. Place the other washer (1b) on the end of the shaft
(1a) where the hole is located.
3. Secure the shaft (1a) with the split pin (1c).
4. Sit on the driver's seat (1).
5. Pull the adjustment lever (1d) backwards and ad-
just the driver's seat (1) to a position that suits you.
6. Release the adjustment lever (1d).
7. Make sure that you can reach the control levers
and the pedals safely.
9.7 ) L W WKH FRYHU SODWH ) L J PRGHO ZLWK
FROOHFWLRQEDVNHW
1. Align the mounting holes on the cover plate (19) at
the rear of the product accordingly.
2. Fit the cover plate (19) using the hexagonal screws
(19a) and hexagonal nuts (19b) provided. Use an
open-ended spanner size 8/10 mm (30).
9.8 0RXQWWKHWUDLOHUDWWDFKPHQWRQWKHFRYHU
SODWH ) L J PRGHOZLWKFROOHFWLRQEDVNHW
1. Align the drawbar (18b) with the mounting holes
on the top of the cover plate (19).
2. Fit the drawbar (18b) using the hexagonal bolts
(18a) provided. Use an open-ended spanner size
8/10 mm (30).
3. Insert the trailer attachment (18) into the drawbar
(18b) from the upper position and secure it with
the split pin (18c).
9.9 ) L WWLQJWKHWUDLOHUDWWDFKPHQW) L J
1. Align the drawbar (18b) with the mounting holes at
the rear of the product.
2. Fit the drawbar (18b) using the hexagonal bolts
(18a) provided. Use an open-ended spanner size
8/10 mm (30).
3. Insert the trailer attachment (18) into the drawbar
(18b) from the upper position and secure it with
the split pin (18c).
9.10 ) L W EUDFNHWV D ) L J PRGHO ZLWK
FROOHFWLRQEDVNHW
1. Align the bracket (20/20a) with the mounting holes
on the rear of the product.
2. Fit the bracket (20/20a) using the hexagonal bolts
M8 (20b), spring washers (20c) and washers
(20d) provided. Use an open-ended spanner size
8/10 mm (30).
3. Repeat the process with the bracket (20/20a) on
the other side.
9.11 $ V VHPEOLQJWKHFROOHFWLRQEDVNHW
) L JV
1. Align the mounting holes on the front frame (21d)
and the top frame (21e).
2. Assemble the front frame (21d) with the top frame
(21e). Use the 8/10 mm open-ended spanner (30)
and the 10/13 mm open-ended spanner (30a) for
this.
3. Fit the side support rods (21a) on both sides to
the front and top frames (21d/21e). To do this,
use the hexagonal screws (21b), hexagon nuts
(21c), open-ended spanner size 8/10 mm (30) and
open-ended spanner size 10/13 mm (30a).
4. Place the collection bag (21f) on the frame and
hook the tabs into the appropriate places.
5. Insert the sheet metal nuts (21i) into the corre-
sponding locations in the container cover (21g).
6. Fit the container cover (21g) by screwing the eight
hexagonal bolts (21h) through the top frame (21e)
from lower using the sheet metal nuts (21i). Use
an open-ended spanner size 8/10 mm (30).
7. Insert the tilt lever (21j) into the container lid (21g)
from above.
8. Fit the hexagonal screw (21k) with the hexagonal
nut (21l) to secure the tilt lever (21j). Use the 8/10
mm open-ended spanner (30) and the 10/13 mm
open-ended spanner (30a) for this.

10. Before commissioning

m � $ W W H Q W L R Q �
$ O Z D ? V � P D N H � V X U H � W K H � S U R G X F W
E H I R U H � F R P P L V V L R Q L Q J �
m : $ 5 1 , 1 *
+ H D OW K KD] D U G
Inhalation of petrol/lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
- Do not breathe petrol/lubricating oil vapours and
exhaust gases.
- Operate the product outdoors only.
Before starting up each time, check the product for
the following:
• Leak-tightness of the fuel system
• Faultless condition and completeness of the guards
and the cutting device
• Tight fit of all screw connections
• Smooth running of all moving parts.
Check before each commissioning,
• whether the cutting tool and the entire cutting
unit (mowing blade, blade coupling, blade brake,
mounting bolts, mowing unit housing) are in perfect
condition. Particular attention must be paid to se-
cure seating, damage and wear.
• whether the tank cover is screwed on tightly.
www.scheppach.com
GB | 41