Yamaha MT400 Bedienungsanleitung Seite 25

5
Press the [PAUSE] button, then the
button.
REC
Tracks 1 and 2 REC SELECT indicators light up contin-
uously and the MT400 enters recording pause mode.
6
Set the fader on each input channel and the
STEREO fader to the 7–8 mark.
7
While checking the level meters, adjust the
recording level using the GAIN controls and
faders on Input Channels 1–4, and the
STEREO fader. Also adjust the stereo position
of the sound sources using the PAN controls
on Input Channels 1–4.
It is best to first play each source while adjusting the
GAIN controls, then use the input channel faders and
the STEREO fader to obtain a good balance between
the sounds.
8
Set the monitor select switch to "CUE" and
use the CUE controls to adjust the
monitoring level on Tracks 1 and 2.
You can monitor the recording sources for Tracks 1
and 2 (in this example, Input Channel 1–4 signals) via
the CUE bus.
MIC/LINE INPUT 1 MIC/LINE INPUT 2
1
GAIN GAIN
LINE MIC LINE
HIGH HIGH
–12 +12 –12
MID MID
–12 +12 –12
LOW LOW
–12 +12 –12
AUX AUX
1 1
0 10 0
AUX AUX
2 2
0 10 0
MIX CUE MIX
0 10 0
MIC/LINE TAPE MIC/LINE
to L to R
MIC/
TAPE TAPE
LINE
INPUT-FLIP INPUT-FLIP
PAN PAN
L R L
10 10
9 9
8 8
7 7
6 6
5 5
4 4
3 3
2 2
1 1
0 0
MIC/LINE INPUT 3 MIC/LINE INPUT 4
2 3
GAIN
MIC LINE MIC
HIGH
+12 –12 +12
MID
+12 –12 +12
LOW
+12 –12 +12
AUX
1
10 0 10
AUX
2
10 0 10
CUE MIX CUE
10 0 10
TAPE MIC/LINE TAPE
to L
MIC/ MIC/
TAPE
LINE LINE
INPUT-FLIP
PAN
R L R
10 10
9
8
7
6
5
4
3
2
1
0
Signal flow during multi-channel mixing
Note: The CUE bus monitoring signal is monaural.
If you wish to monitor a stereo signal, set the
monitor select switch to "STEREO" to select the
Stereo bus instead of the CUE bus. (This is
convenient if you wish to check the stereo position of
each channel.)
9
Adjust the level and pan of each channel
signal while monitoring the sound through
the headphones or the audio system. Adjust
tonal quality, if necessary, with the EQ
controls.
0
Press the [PAUSE] button to cancel pause
mode and start recording.
A
Press the [STOP] button to stop recording.
Tracks 1 and 2 REC SELECT indicators flash.
B
Rewind the tape to the beginning and listen
to the recording.
If you are satisfied with the recording, set the [REC
SELECT] switches on Tracks 1 and 2 to "OFF".
4
GAIN
LINE MIC
HIGH
–12 +12
MID
–12 +12
LOW
–12 +12
AUX
1
0 10
AUX
2
0 10
MIX CUE
0 10
MIC/LINE TAPE
to R
MIC/
TAPE
LINE
INPUT-FLIP
PAN
Stereo bus
L R
9
8
7
6
5
4
3
2
1
0
PHONES
MONITOR OUT
STEREO OUT
STEREO
L
10
9
Track 1
8
7
6
5
4
Track 2
3
2
R
1
0
Track 3
Track 4
—Owner's Manual
23