Turning On The Mt400; Loading A Cassette Tape; Recording The First Track; Preparation Before Recording - Yamaha MT400 Bedienungsanleitung

14

Turning On the MT400

1. Make sure that the plug of the supplied AC
adapter is securely connected to the DC12V
jack on the rear of the MT400.
2. Plug the other end of the AC adapter into a
suitable AC outlet.
3. Press the POWER switch on the rear panel of
the MT400. The POWER indicator in the
meter section lights up.

Loading a Cassette Tape

Before loading a cassette tape, make sure the tape is
not slack inside the cassette. Also, make sure the write-

Recording the First Track

The MT400 allows signals input at MIC/LINE INPUT 1–4 to be directly recorded on Tracks
1–4 respectively (this is called "direct recording"). Connecting a sound source to MIC/LINE
INPUT 1 will automatically select Track 1 for recording, and connecting another sound
source to MIC/LINE INPUT 3 will automatically select Track 3 for recording. This is
convenient for recording one sound source at a time.
This section explains how to record the first sound source in Track 1.

Preparation Before Recording

1
7
C
A
2
8
—Owner's Manual
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE TAPE TAPE TAPE
LINE LINE LINE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
protect tabs are not broken. If they are broken, you
cannot record on the tape.
1. Open the cassette compartment cover.
2. Load the cassette into the compartment with
the A side facing up.
3. Close the cassette compartment cover.
If it is a new tape, fast forward and rewind it once to
prevent binding, which may occur due to the tape
being tightly wound during manufacturing.
4. Press the [PLAY] button to start playback, and
stop after about 20 seconds.
It is best not to use the first and last 20 seconds of a
tape, as the splice between the leader and tape can
cause distortion.
STEREO INPUT
5 6 7 8
L R L R 1
2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
+
–
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
B 0 6
9
+6
POWER
+3
0
–5
–10
3 4
3
METER SELECT
4
4 4TR
OFF STEREO
R
FF STOP PAUSE
5