Yamaha MT400 Bedienungsanleitung Seite 38

36
GAIN
6
LINE
HIGH
–12
MID
–12
LOW
–12
AUX
1
0
AUX
2
0
MIX
8
0
MIC/LINE
3
to L
TAPE
INPUT-FLIP
PAN
L
10
9
8
7
6
5
4
3
2
1
0
1
Connect a sound source to punch in to MIC/
LINE 4.
2
Connect a footswitch to the PUNCH IN/OUT
jack.
3
Set the [INPUT-FLIP] switches on Input
Channels 1–4 to "MIC/LINE (
4
Set the [REC SELECT] switch on Tracks 4 to
" ".
4
The Track 4 REC SELECT indicator flashes.
5
Set the [METER SELECT] switch to "
6
While watching the level meter, use the GAIN
control and the fader on Input Channel 4 to
adjust the input level of the sound source.
7
Set the monitor select switch to "CUE".
8
Start playing the tape and use the CUE
controls on Input Channels 1–4 and the
MONITOR LEVEL control to adjust the
monitoring level.
—Owner's Manual
1
4 5
3 L
1 2 3 4 5 –6
L
GAIN GAIN GAIN LEVEL
0
MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH
+12 –12 +12 –12 +12 –12 +12
MID MID MID
MULTITRACK CASSETTE RECORDER
+12 –12 +12 –12 +12 –12 +12
LOW LOW LOW
+12 –12 +12 –12 +12 –12 +12
AUX AUX AUX
1 1 1
10 0 10 0 10 0 10
AUX AUX AUX
2 2 2
10 0 10 0 10 0 10
CUE MIX CUE MIX CUE MIX CUE
10 0 10 0 10 0 10
TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE TAPE TAPE
LINE LINE LINE LINE
LEVEL
INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN
MIN
R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
".
4TR
STEREO INPUT
6 7 8
R L R 1
2
7 –8
R L R
LEVEL
+6
+3
10 0 10
0
–5
–10
REC
1 2 3
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3 4
OFF OFF OFF OFF
L R L R
4.8/ 9.5
– +
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
STEREO
ST+CUE
CUE
MAX
STEREO
REC PLAY REW FF
9
PHONES
2
9
Locate a position before the point at which
you want to punch in, and press the [PLAY]
button.
Playback on Tracks 1–4 starts.
Note: Punch in/out recording with a footswitch does
not use the
REC
button at this point accidentally, recording
REC
will start immediately.
0
At the point where you want to punch in,
press the footswitch once and start playing
the sound source.
Recording starts as soon as you step on the footswitch.
You will hear the new sound play back instead of the
existing sound.
A
At the point where you want to punch out,
press the footswitch again.
Recording stops as soon as you step on the footswitch,
and you will hear the existing sound playback via the
CUE control on Input Channel 4.
B
Press the [STOP] button to stop playback.
+6
POWER
+3
0
–5
–10
4
4
METER SELECT
5
4TR
STEREO
7
STOP PAUSE
0, A
B
PUNCH I/O
button. If you press the