Applying Effects At Mixdown - Yamaha MT400 Bedienungsanleitung

Applying Effects at Mixdown

One of the typical uses of external effects processors connected to AUX SENDs is to apply
reverb effects to track signals during mixdown. In this case, you can adjust the amount of
effects for each track individually using the AUX 1 and AUX 2 controls.
4
5
2
1
Connect AUX SEND 1 to the input of an
effects processor, and connect the outputs of
the effects processor to STEREO INPUT 5L/6R.
Set the effects processor so that it will output
only the processed signal.
2
Set the [INPUT-FLIP] switches on Input
Channels 1–4 to "TAPE (
Tracks 1–4 signals are sent to Input Channels 1–4.
3
Set the monitor select switch to "STEREO".
4
While playing the tape, use the faders, PAN
controls and EQ controls on Input Channels
1–4 to adjust the volume balance, stereo
image, and tonal quality of each track.
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE LINE TAPE LINE TAPE LINE TAPE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
1
STEREO INPUT
5 6 7 8
L R L R
1 2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
– +
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
5
Turn up the AUX 1 control of the input
channel to which you wish to apply effects.
Channel signals (playback sound of Tracks 1–4) are
sent to the effects processor connected to AUX SEND
1. Adjust the input level on the effects processor, if
necessary.
6
Turn up the LEVEL control for STEREO INPUT
5L and 6R.
The processed signal is returned from the effects
processor and added to the Stereo bus of the MT400.
The more you turn up the LEVEL control, the more
effects you can obtain.
6
+6
POWER
+3
0
–5
–10
3 4
METER SELECT
4 4TR
OFF STEREO
R
3
FF STOP PAUSE
—Owner's Manual
33