Video Settings - Yamaha RX-V1800 Bedienungsanleitung

Front panel display scroll FL SCROLL
Use this feature to set the mode to display the iPod menu
(such as song title or channel name) in the front panel
display.
Choice
CONT Continuous mode.
Select this to display the operation status in the
front panel display in a continuous manner.
ONCE Scroll-once mode.
Select this to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.

Video settings

B)VIDEO SET
B)VIDEO SET
.
VIDEO CONV.;;;;;;ON
COMPONENT I/P;;;OFF
HDMI SCALING;;;480p
HDMI ASPECT;;;THRGH
[ ]/[ ]:
[p]/[[]:
Video conversion VIDEO CONV.
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO, and COMPONENT
VIDEO jacks.
Choice
ON Converts composite, S-video, and component
video signals interchangeably and up-converts
composite, S-video, and component video
signals to HDMI video signals.
OFF Does not convert any signals.
Notes
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted into the S-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The analog component video signals with 1080p of resolution
are only output at the COMPONENT VIDEO MONITOR OUT
jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted into component video signals, the picture quality may
suffer depending on your VCR.
• Set "VIDEO CONV." to "ON" to display the sound field
parameter display and short message display.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set "VIDEO CONV." to "OFF".
Functions
UP/DOWN
Select
Functions
Customizing this unit (MANUAL SETUP)
Component interlace/progressive up-conversion
COMPONENT I/P
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
Choice
ON Activates the analog interlace/progressive up-
conversion of the analog video signals.
OFF Deactivates the analog interlace/progressive up-
conversion of the analog video signals.
Notes
• The "COMPONENT I/P" parameter appears only when you set
"VIDEO CONV." to "ON".
• If your video monitor does not support analog video signals
with 480p/576p of resolution, the SET MENU items may not be
displayed on your video monitor when "COMPONENT I/P" is
set to "ON". In such a case, set the "COMPONENT I/P"
parameter to "OFF".
HDMI scaling HDMI SCALING
Use this feature to activate or deactivate the HDMI up-
scaling of the analog video signals input at the VIDEO, S
VIDEO and COMPONENT VIDEO jacks so that the up-
scaled video signals are output at the HDMI OUT jack.
This unit up-scales the video signals as follows:
• 480i (NTSC)/576i (PAL) → 480p/576p, 1080i, 720p or
1080p
• 480p/576p → 1080i, 720p or 1080p
Choice
THROUGH Does not up-scale any analog video signals.
480p (or
Up-scales analog video signals to 480p or 576p,
1080i, 720p, or 1080p of resolution.
576p), 1080i,
720p, 1080p
Note
This unit does not up-scale the analog component video signals
with 720p or1080i of resolution.
Functions
Functions
89
En