Kenwood Cooking Chef experience KCL95.429SI Bedienungsanleitungen Seite 8

Before plugging in
Make sure your electricity supply is the same as the one shown on the underside of your appliance.
WARNING: THIS APPLIANCE MUST BE EARTHED.
This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to come into contact with food.
This appliance is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Before using for the first time
Wash the parts: see 'Care and Cleaning'.
Know Your Kenwood Cooking Chef
Key
Attachment outlets
High speed outlet (HSO)
1
Slow speed outlet (SSO)
2
Bowl tool socket
3
Stir tool socket
4
Mixer
High speed outlet cover
5
Mixer head
6
Slow speed outlet cover
7
Cooking chef bowl
8
Head - lift lever
9
Control dial
10
On/Off switch
11
Display screen
12
Work surface protection mat
13
Drain hole
14
Bowl pedestal/induction area
15
Air vents
16
Temperature sensors
17
Heat shield
18
Rubber seal (removable)
19
Splashguard
20
Feed chute lid
21
K-beater
22
High temperature creaming beater
23
Whisk
24
Dough tool
25
Stir tool
26
Stir assist clip
27
High temperature spatula
28
Dough scraper
29
Spanner
30
Steamer Attachment
Handle supports
31
Supporting ring
32
Folding handles
33
Removeable tray
34
Egg holders
35
Note: Slow Speed outlet attachments
The slow speed outlet on your Stand mixer model features
the Twist Connection System. It is designed to accept Twist
Connection System attachments.
When purchasing new attachments for the slow speed outlet
you should check compatibility with your Stand mixer. All
Twist Connection System attachments can be identified by the
product code which starts with KAX and also by the Twist logo
which is visible on packaging.
If you own attachments featuring the Bar Connection System
you will need to use the KAT002ME adaptor to connect
these to the Twist Connection System
mixer.
on your Stand
4
For more information visit
www.kenwoodworld.com/twist.
Connecting to Kenwood World App
A
Refer to Illustrations –
The Kenwood World App will allow you to control your
appliance through your smart phone or tablet.
1 Plug in and press the On/Off switch on the side of the
power unit.
2 Select Settings > WiFi > Connect and follow the
instructions on the touch screen.
PIN number
This will be required when prompted by the Kenwood
World App.
The appliance can only be connected when the PIN
Number is shown on the display screen. If the PIN is
entered incorrectly, follow the instructions on the app and
retry.
To display the unit's PIN number, select Settings
> WiFi > Connect and follow the instructions on the display
screen (only when connected to WiFi).
Note:
WiFi
Operates with IEEE802.11 b, g and n at 2.4 GHz only. xxj
Compatibility
Kenwood World App compatible with latest versions of iOS
and Android.
Factory reset
Important
When disposing of the appliance, it is important to factory
reset it to protect your personal data.
Selecting this option will erase all WiFi data stored on the
appliance and restore it to factory settings.
To factory reset your appliance, select Settings
>Factory Reset.
To Set Up Your Cooking Chef Connect
E
Refer to Illustrations –
IMPORTANT
Make sure the induction area, temperature sensors and
external surface of the bowl base are clean. Failure to do
this will affect the heat sensor, resulting in poor cooking
performance.
Check that all the outlet covers including the heat shield
are fitted. If they are not correctly fitted the heating
function will not operate.
1 Plug in and press the On/Off switch.
2 Turn the head-lift lever clockwise and raise the mixer head
until it locks.
3 Push the heat shield upwards onto the underside of the
mixer head until fully located. The heat shield must never
be used without the rubber seal fitted correctly.
If using the Cooking Chef Connect without heat, it is
not necessary to fit the heat shield unless using the
splashguard. Refer to 'To Fit and Use Your Splashguard
Assembly' section.
4 Fit the bowl to the base.
5 Place the required tool in the bowl tool socket or stir tool
socket if using the stir tool, locating the pin in the groove
and then turn to lock into position.
D
I