Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Tool Height Adjustment
Refer to Illustration
U
Whisk, Stainless Steel K-beater
For best performance the whisk and K-beater should be
almost touching the bottom of the bowl. If necessary adjust
the height using the spanner provided.
High Temperature Creaming Beater - this tool should just
touch the bottom of the bowl.
1
Unplug the appliance.
2
Raise the mixer head and insert the whisk, K-beater or high
temperature creaming beater.
3
Lower the mixer head. If the clearance needs to be
adjusted, raise the mixer head and remove the tool.
4
Using the spanner provided loosen the nut sufficiently to
allow adjustment of the shaft. To lower the tool closer to
the bottom of the bowl, turn the shaft anti-clockwise. To
raise the tool away from the bottom of the bowl turn the
shaft clockwise.
5
Re-tighten the nut.
6
Fit the tool to the mixer and lower the mixer head. (Check
its position see points above).
7
Repeat the above steps as necessary until the tool is set
correctly. Once this is achieved tighten the nut securely.
Dough Tool - this tool is set at factory and is not adjustable.
Stir Tool - this tool should just touch the bottom of the bowl.
1
Unplug the appliance.
2
Raise the mixer head and insert the stir tool.
3
Lower the mixer head. If the tool needs adjustment, raise
the mixer head and use the spanner to loosen the nut, then
lower the mixer head.
4
To lower the tool closer to the bottom of the bowl, turn the
adjustment wheel clockwise. To raise the tool away from
the bottom of the bowl, turn the adjustment wheel anti-
clockwise.
5
Re-tighten the nut.
To Fit And Use Your Splashguard Assembly
Refer to Illustration
V
The splashguard assembly consists of 2 pieces: the heat shield
and the splashguard.
The heat shield is to protect the mixer head from steam
produced during the cooking process.
The splashguard should not be fitted to the bowl unless used
in conjunction with the heat shield.
1
Raise the mixer head until it locks.
2
Push the heat shield upwards onto the underside of the
mixer head until fully located. The heat shield must never
be used without the rubber seal correctly fitted.
3
Fit the bowl onto the base.
4
Lower the mixer head.
5
Rest the splashguard on the bowl rim and then slide
forward until fully located.
•
During mixing, ingredients can be added directly to the
bowl via the feed chute.
6
To remove the splashguard simply slide it away from the
appliance.
Note: The splashguard will remain attached to the heat shield
when the mixer head is raised unless removed before lifting
the mixer head.
7
To remove the heat shield, raise the mixer head until
it locks. Remove the tool, then pull the heat shield
downwards from the underside of the mixer head.
Note: Only fit or remove the splashguard when the mixer
head is in the locked position.
To Fit And Remove Your Stir Assist Clip
Refer to Illustration
W
The stir assist clip can be used to assist the mixing action.
1
Slot the stir assist clip over the side of the bowl with the
vertical ridge on the inside and the clips on the outside.
2
Turn the clip anti-clockwise onto the bowl handles.
3
To remove, reverse the procedure.
IMPORTANT - The stir assist clip should not be fitted when
using the K-beater, whisk, dough tool or creaming beater.
Assembling The High Temperature
Creaming Beater
Refer to Illustration
X
Fitting The Wiper Blade
The wiper blade is supplied already fitted and should always
be removed before cleaning.
1
Carefully fit the flexible wiper blade onto the tool by
locating the base of the wiper blade into the slot then fit
one side into the groove before gently hooking the end in
place. Repeat with the other side.
Care And Cleaning
Always switch off and unplug before cleaning.
A little grease may appear at outlet
it. This is normal - just wipe it off.
The metal surfaces of the temperature sensors may show
signs of wear during normal use. This does not affect the
performance of the product.
Do not leave the high temperature flexible beater fitted to
the mixer when not in use.
Appliance, outlet covers
Wipe with a damp cloth, then dry.
Never use abrasives or immerse in water.
High temperature creaming beater
Always remove the flexible wiper blade from the tool
before cleaning.
Wash the flexible wiper blade and tool in hot soapy water,
then dry thoroughly. Alternatively the parts can be washed
in a dishwasher.
Note: Please inspect the condition of the tool body before and
after use and also regularly inspect the condition of the wiper
blade and replace it if there are any signs of wear.
Bowl, Tools, Splashguard, Stir Assist Clip
Wash by hand, then dry thoroughly or wash in the
dishwasher (refer to chart at front of manual).
Never use a wire brush, steel wool or bleach to clean your
stainless steel bowl. Use vinegar or a suitable descaler to
remove limescale.
If food sticks or burns on the inside of the bowl, remove as
much as possible using the spatula provided. Fill the bowl
with warm soapy water and allow to soak. Remove any
stubborn deposits using a nylon brush.
Any discolouration of the bowl will not affect its
performance.
Drain Hole
Ensure this area is free from food. If necessary use a pipe
cleaner or cotton bud to clean.
Temperature sensors
Wipe with a damp cloth then dry thoroughly. Never use
abrasives or sharp instruments to clean the sensors.
13
when you first use
Werbung
