Product Description And Specifications - Bosch GSK 50 Originalbetriebsanleitung

OBJ_BUCH-1038-003.book Page 14 Friday, August 17, 2012 10:59 AM
14 | English
Safety Warnings for Compressed-air
Nailers/Staplers
Wear safety goggles.
Always assume that the pneumatic tool is loaded
with fasteners. Careless handling of the pneumatic
tool can lead to unexpected shot actuation of fasteners
and cause injury.
When working, hold the pneumatic tool in such a
manner that your head and body cannot be injured in
case of sudden kickback due to a malfunction of the
energy supply or from hard objects/locations in the
workpiece.
Never point the pneumatic tool at yourself or at per-
sons close by. Unexpected actuation will expel a fas-
tener, which can lead to injury.
Do not actuate the pneumatic tool until firmly placed
against the workpiece. When the pneumatic tool is not
in contact with the workpiece, the fastener can bounce
away from the fastening point and overload the pneu-
matic tool.
Do not work on ladders or scaffolds
when the actuation system "Contact ac-
tuation" is set. In particular, do not move
from one fastening location to another,
close boxes or enclosures, or fasten
transport-securing fixtures on e.g., vehi-
cles and waggons, via scaffolds, stairs,
ladders or ladder-like constructions,
such as roof battens. With this actuation
system, a fastener will be discharged each
time when accidentally applying the pneu-
matic tool while the discharge lock-off is
pressed in. This can lead to injury.
Observe the conditions of the job site. It is possible
that fasteners can burst through thin workpieces or be
deflected when working in corners or against edges,
and harm persons.
Technical Data
Compressed-air nailer
Article number
Driving force
at 6.3 bar (91 psi)
Actuation systems
– Single actuation with safety run
– Contact actuation
Fastener
– Type
– Length
– Diameter
Magazine capacity, max.
Engine oil SAE 10, SAE 20
Internal volume
Max. working pressure
Connecting thread
Supply-air hose
– Max. operating pressure at 20 °C
– Inner diameter of hose
– Max. hose length
Air consumption per driving procedure
at 6.8 bar (100 psi)
Dimensions
– Height
– Width
– Length
Weight according to EPTA-Procedure 01/2003
1 609 929 U13 | (17.8.12)
Disconnect the air supply, when the fas-
tener is jammed in the pneumatic tool.
When the pneumatic tool is still connected
to the power supply, it can accidentally be
actuated when removing a jammed fasten-
er.
Use caution when removing a jammed or stuck fas-
tener. The system can be under tension and cause the
fastener to be shot or thrust out, while attempting to
clear the jam.
Do not use this to pneumatic tool to fasten electrical
wiring. It is not suitable for fastening electrical wiring,
can damage the insulation of electric cables and thus
lead to electric shock and danger of fire.
Never use oxygen or flammable gases as the energy
source for the pneumatic tool. Flammable gases are
dangerous and can cause the pneumatic tool to ex-
plode.
Use appropriate detectors to determine if utility
lines are hidden in the work area or call the local util-
ity company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage.
The pneumatic tool may only be connected to lines,
for which the maximal permissible pressure of the
pneumatic tool cannot be exceeded by more than
10 %; for higher pressures, a pressure control valve
(pressure reducer) with preceding pressure-limita-
tion valve in the compressed-air line must be in-
stalled. Excessive pressure leads to abnormal opera-
tion or breakage of the pneumatic tool, which can lead
to injury.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Nm
mm
mm
ml
ml
bar
"
bar
"
m
l
mm
mm
mm
kg
Intended Use
The pneumatic tool is intended for connecting work in roof-
ing, encasing, battening, manufacturing wall and ceiling el-
ements, wood facades, pallets, wood fences, noise-reduc-
tion walls and boxes.
Only the fasteners (nails, staples, etc.) specified in table
"Technical Data" may be used.
Product Features
The numbering of the product features refers to the illus-
tration of the pneumatic tool on the graphics page.
1 Workpiece protector
2 Discharge lock-off
3 Thumbwheel for depth stop adjustment
4 Air outlet with adjustable exhaust cap
5 Handle
6 Air connector
7 Magazine-slider lock (GTK 40)
8 Magazine
9 Selector switch for actuation system
10 Trigger
11 Magazine slider (GTK 40)
12 Clamping lever for opening/closing the shot duct
(GTK 40)
13 Outlet
14 Magazine lock (GSK 50)
15 Refill indicator (GSK 50)
16 Air-connection coupling
17 Supply-air hose
18 Staple strip*
19 Nail strip*
20 Magazine rail (GSK 50)
21 Driver blade
22 Storage for workpiece protector
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accesso-
ries can be found in our accessories program.
GTK 40
3 601 D91 G..
18.4
Staple strip
13–40 15, 19, 25, 30, 35, 40, 45, 50
1.2
100
0.25–0.5
196.5
5–8
¼
10
¼
30
0.71
246
60
272
1.14
GSK 50
3 601 D91 D..
17.8
Nail strip
Brads
1.2
100
0.25–0.5
200
5–8
¼
10
¼
30
0.69
251
60
260
1.14
Bosch Power Tools