Product Description And Specifications - Bosch GCN 45-15 Professional Originalbetriebsanleitung

OBJ_BUCH-1303-001.book Page 16 Friday, March 25, 2011 11:07 AM
16 | English
ceeded by more than 10 %; for higher pressures, a pressure con-
trol valve (pressure reducer) with preceding pressure-limitation
valve in the compressed-air line must be installed. Excessive pres-
sure leads to abnormal operation or breakage of the pneumatic tool,
which can lead to injury.

Product Description and Specifications

Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Intended Use
The pneumatic tool is intended for connecting work in roofing, encasing,
battening, manufacturing wall and ceiling elements, wood facades, pal-
lets, wood fences, noise-reduction walls and boxes.
Only the fasteners (nails, staples, etc.) specified in table "Technical Data"
may be used.
Product Features
The numbering of the product features refers to the illustration of the
pneumatic tool on the graphics page.
1 Air outlet
2 Handle
3 Air connector
4 Magazine lock
5 Trigger, when working with single actuation
6 Magazine
7 Magazine cover
8 Trigger, when working with contact actuation
9 Outlet
10 Discharge lock-off
11 Thumbwheel for depth stop adjustment
12 Air-connection coupling
13 Supply-air hose
14 Rubber ring
15 Locking pin
16 Actuation lever
17 Actuation spring
18 Actuation bolt
19 Magazine spindle
20 Nail role*
21 Shot duct
22 Feeder hook
23 Guide groove
24 Driver blade
25 Spacer block
26 Button for spacer block adjustment
*Accessories shown or described are not part of the standard delivery scope of
the product. A complete overview of accessories can be found in our accessories
program.
Noise/Vibration Information
Measured noise values determined according to EN 12549.
Typically the A-weighted noise levels of the pneumatic tool are: Sound
pressure level 92 dB(A); sound power level 105 dB(A). Uncertainty
K=2 dB. Wear hearing protection!
1 609 929 X29 | (25.3.11)
Overall vibrational values determined according to EN ISO 20643:
Vibrational emission value a =3.2 m/s
h
Technical Data
Compressed-air nailer
Article number
Driving force
at 6.3 bar (91 psi)
Actuation systems
– Single actuation with safety run
– Contact actuation
Fastener
– Type
– Length
– Diameter
Magazine angle
Magazine capacity, max.
Engine oil
SAE 10, SAE 20
Internal volume
Rated pressure
Connecting thread
Supply-air hose
– Max. operating pressure at 20 °C
– Inner diameter of hose
– Max. hose length
Air consumption per driving procedure
at 6.8 bar (100 psi)
Dimensions
– Height
– Width
– Length
Weight according to EPTA-Procedure
01/2003
Declaration of Conformity
We declare under our sole responsibility that the product described un-
der "Technical data" is in conformity with the following standards or
standardization documents: EN 792 according to the provisions of the di-
rectives 2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 25.03.2011
2 2
. Uncertainty K =1.5 m/s .
GCN 45-15
Professional
3 601 D91 C..
Nm 37.3
Nail role
Roofing nails
mm 19 45
–
mm 3
° 15
120
ml 0.25 0.5
–
ml 362
bar 5 8
–
" 3/8
bar 10
" 3/8
m 30
l 1.3
mm 267
mm 133
mm 270
kg 2.5
Bosch Power Tools