Technical Specifications; Operation - Kärcher CB 2 exclusiv 23 Originalbetriebsanleitung

Bleed dosing pump.
1 Ventilation lever
2 Ventilation button
3 Adjustment knob dosing volume
The compressed air supply of the system
must be operating.
 Turn the ventilation lever in an anti-
clockwise direction until it stops.
 Set the dosing volume to 100%.
 Press the ventilation key until the deter-
gent emerges from the ventilation line
at the bottom of the dosing pump with-
out bubbles.
 Set the dosing volume to the required
value.
 Turn the ventilation lever in a clockwise
direction until it stops.

Technical specifications

Dimensions
Plant dimensions
CB 2/
23
Height mm 3215 3415 3715
Width mm
Depth *) mm
Vehicle size limits dimensions **)
Washing mm
width
Washing mm 2300 2500 2800
height
Washable vehicle lengths ***)
without safety mm
distance
with safety mm
distance
Hall width
with safety mm
distance
without safety mm
distance
>*) Rotating roof brush, rotating side
brushes **) almost all vehicles can be
washed within these measurements ***)
with 9000 mm drive channel length
Wash brushes
Diameter of side-brushes
Side
Side-brush rotation speed 1/min
Diameter of brush Roof
Brush rotation speed
Roof
Portal drive speed
Sound level
Brush cleaning
Drier operation
Electrical connection
Voltage**
Voltage fluctuations
(max)
Frequency
Connection output Ba-
sic plant
Connecting line with
side blower and/or hot
wax bliler
Pre-securing Control
cabinet *
* to be provided at installation site accord-
ing to the local requirements
**Supplying voltage by means of the gen-
erator is prohibited
CB 2/ CB
Water connection
25 2/28
Nominal width
Flow pressure accord-
3500
ing to DIN 1988 (with
2020
100 l/min)
Temperature
2300
Fresh water consump-
tion *)
Sevice water consump-
tion *)
*) Water consumption/vehicle at 0.45 MPa
5800
(program-related for 4.5 m vehicle length),
with water conditioning (option)
5270
Compressed air connection
Nominal width
Pressure
4500
Supply capacity, min.
4050
Consumption/Washes
(without anti-frost de-
vice, programme-de-
pendent with 4.5 m ve-
hicle length)
Use in frost protection
Features
mm 965
107
mm 880
1/min 127
m/min 0...20
dB(A) 67
dB(A) 87
Connection values
V 400±10%/
3~, P, N
V 5%
Hz 50
kW 10
kW 16
A max. 35
Inch 1
MPa 0,4...0,6
(bar) (4...6)
°C max. 50
l 25...60
l 71...300
Inch 1/2
MPa 0,6...0,8
(bar) (6...8)
I/min 300
l 50
l approx.
700
6
-
EN

Operation

In the event of danger for persons, property
and animals, the plant must be switched off
immediately by pressing the emergency-
stop button. It is found
– at the wash card/code reader
– at the operating place for manual oper-
ator station
– at the entrance to the wash hall, íf an
operating point or wash card/code
reader is located there.
ATTENTION
Risk of damage to vehicle to be cleaned. If
a malfunction of the washing bay occurs af-
ter the detergent has been applied, it must
be switched off and the detergent removed
by spraying the vehicle thoroughly with wa-
ter to prevent the paintwork from being
damaged through an extended period of
exposure to the detergent.
Note:
With self-service systems a specialist who
is familiar with the plant must be available
to carry out or arrange for measures that
are necessary to prevent potential dangers.
Switching on after emergency-stop
Note:
Prior to the restart, the cause for the activa-
tion of the emergency stop button has to be
remedied. Persons or animals may not re-
main in the working area. Vehicles must be
driven out of the system.
1 Emergency-stop button
2 Control supply voltage/normal position
button
 Release emergency-stop button by
pulling it.
 Set automatic/manual switch at the
feeder to automatic.
 Press control supply voltage/normal po-
sition button on the operating point for
manual mode.
In the normal position, the above green sig-
nal light "forward" of the vehicle positioning
traffic light lights up. The plant is again
ready for operation and the vehicle being
washed can be driven in.
Start up
 Stop valve opens for water and com-
pressed air.
 Set main switch on the feeder to "1".
 Set automatic/manual switch to auto-
matic.
 Press control supply voltage/normal po-
sition button on the operating point for
manual mode.
The plant is again ready for operation and
the vehicle being washed can be driven in.
31