Kärcher CB 2 exclusiv 23 Originalbetriebsanleitung Seite 41

Display Fault
50 Limit switch FA (drive start) has not been
exited despite driving command
51 Limit switch FA (Drive start) has not
reached expected position
52 Limit switch FE (drive end) has not been
exited despite driving command
53 Limit switch FE (Drive end) has not
reached expected position
54 Travel command has been given but
SB1A (side brush 1, outward) limit switch
has not been exited
55 Limit switch SB1A (side brush 1, outward)
has not reached expected position
56 Travel command has been given but
SB1E (side brush 1, driven-in) limit switch
has not been exited
57 Limit switch SB1E (side brush 1, driven-in)
has not reached expected position
58 Travel command has been given but
SB2A (side brush 2, outward) limit switch
has not been exited
59 Limit switch SB2A (side brush 2, outward)
has not reached expected position
60 Travel command has been given but
SB2E (side brush 2, driven-in) limit switch
has not been exited
61 Limit switch SB2E (side brush 2, driven-in)
has not reached expected position
62 Travel command has been given but DBO
(top roof brush) limit switch has not been
exited
63 Limit switch DBO (top roof brush) has not
reached expected position
66 Travel command has been given but DBU
limit switch (lower roof brush) has not been
exited
67 Limit switch DBU (lower roof brush) has
not reached expected position
68 Travel command has been given but TRO
(upper roof drier 1) limit switch has not
been exited
69 Limit switch TRO (upper drier 1) not
reached at the expected position
70 Travel command has been given but TRU
(lower roof drier 1) limit switch has not
been exited
71 Limit switch TRU (lower drier 1) not
reached at the expected position
80 Roof brush alignment too high
81 Roof brush alignment too low
83 Roof brush performance during the wash
too low
84 Side-brush 1 alignment too high
85 Side-brush 1 alignment too low
87 Side-brush 1 performance during the wash
too low
88 Side-brush 2 alignment too high
Possible cause
Limit switch activated through foreign
metal or is defective
Limit switch activated through foreign
metal or is defective, drive wheel is turn-
ing
Limit switch defective, drive wheel is
turning
Limit switch activated through foreign
metal or is defective, drive wheel is turn-
ing
Limit switch defective, drive wheel is
turning
Limit switch activated through foreign
metal or is defective, drive wheel is turn-
ing
Limit switch defective, drive wheel is
turning
Limit switch activated through foreign
metal or is defective, drive wheel is turn-
ing
Limit switch defective, drive wheel is
turning
Limit switch is defective
Cable, motor or gears of rotary roof
brushes defective
Motor circuit breaker in the main control
cabinet has tripped.
Cable, motor or gears of rotary roof
brushes defective
Cable, motor or gears of rotary side
brush 1 defective
Motor circuit breaker in the main control
cabinet has tripped.
Cable, motor or gears of rotary roof
brushes defective
Cable, motor or gears of rotary side
brush 2 defective
16
-
EN
Remedy
Check limit switch portal driving for defects;
remove metal parts from the hall floor;
switch off/on the unit, repeat washing pro-
cess
Check limit switch of side brushes for de-
fects; clean upper running surface of the
side-brush holder; switch off/on the unit, re-
peat washing process
Check limit switch for damages, switch on/
off the unit, repeat washing process
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check the motor circuit breaker in the main
control cabinet.
Switch off and switch on the unit, repeat
washing process, call Customer Service
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check the motor circuit breaker in the main
control cabinet.
Switch off and switch on the unit, repeat
washing process, call Customer Service
Switch off and switch on the unit, repeat
washing process, call Customer Service
41