Herunterladen Inhalt Inhalt Diese Seite drucken

Preparation; Content Of Delivery / Necessary Accessories - Reely ROAD Ice Land ARR Bedienungsanleitung

4wd gp monster truck
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

4
P
REPARATION
4.1
C
ONTENT OF DELIVERY
S
COPE OF DELIVERY
-
One Chassis
-
4.6 ccm two stroke glow engine
with 2.15 kW (2.92 PS), with
manifold, resonance tube, air filter and pull starter,
already mounted
-
Steering servo, Throttle/brake servo and receiver,
already mounted
-
fuel hoses, already laid.
-
Four wheels with chrome-plated plastic rims and
already mounted Monster Truck tires
-
Monster-Truck car body, imprinted
-
Decal sheet
-
Splints to fasten car body
-
A plastic tube as guidance for the wire aerial
-
one two-channel remote control
(pistol grip transmitter)
-
these installation and operating instructions
S
P
PARE
ARTS
The spare part list can be found on our Website www.conrad.com in the Download domain specific to the
corresponding product. Alternatively, you can order the spare parts by phone; the contact details are at the
beginning of this operating manual in chapter "Introduction".
A
CCESSORY RECOMMENDATION
Which type of fuel is the right one?
The selection of the fuel has an impact on the performance characteristic of the engine.
However, as a matter of principle:
-
In the running-in phase, a special RC car fuel with approximately 15% nitromethane should be used.
-
After the run-in of the engine (after a mere operating time of approximately 45 minutes), you can change to a fuel
with approximately 20% nitromethane.
-
For maximum output, we recommend the max. percentage of 25% nitromethane
Use fuel for RC cars only!
The percentage of oil contained in fuel for RC plane engines is too small (too little lubrication), which causes the
engine to overheat, thus leading to serious damages.
The same is valid for vehicle gasoline.
Why is a tank bottle needed?
RC model car fuel is available in big bulks (canisters) only. Filling the tank by using a smaller, special tank bottle with a small,
curved pouring tube is significantly simpler. You also prevent spilling fuel (expensive and poisonous).
Are more glow plugs necessary?
Glow plugs wear, especially in the running-in phase. Therefore, we recommend having some glow plugs ready in case of
need for a replacement. There are glow plugs with different calorific values; the selection of the glow plug has a big impact
on driving performance. For the running-in phase, you should use a "hot" glow plug for high performance engines. After the
running-in phase, you can use a glow plug with a middle or a "cold" calorific value.
Use glow plugs for RC cars only! A wrong glow plug, such as e.g. for 4 stroke plane engines, lets the engine
run incorrectly and complicates the tuning.
Replacing the glow plug
To that effect, you need an extra long plug spanner (spider wrench SW 8, 9, 10 and 12), which can be used also to unscrew
the outer hexagonal screws.
Sparking the glow plug
A plug connector (long) with start battery or a plug connector with rechargeable battery as a unit is inserted on the glow
plug and heats the latter, so that the air-fuel mix sparks off and the engine starts. When the engine runs smoothly, the plug
connector can be removed.
© REELY 06/07
,
NECESSARY ACCESSORIES
N
ECESSARY ACCESSORIES
Not included in the delivery
-
batteries or rechargeable batteries (recommended)
for the receiver and the servos
-
Charger (220V) for the rechargeable batteries or
quick charger to connect to a 12V car battery
-
Glow plug (calorific value 1 or 3) and
-
plug spanner
-
Plug connector (long) for start battery and
-
2 Volt start battery or
-
Plug connector with rechargeable battery as a unit
-
Model fuel methanol/oil based, minimum share
5% - 10% nitromethane
-
Tank bottle
39

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ice land rtr

Inhaltsverzeichnis