Stokke Xplory Benutzerhandbuch Seite 25

38
EN
Folding. (1-3) SEAT Dissasembly (7)
STOKKE® XPLORY® back wheels: Press the service handles in on each side of
1. All four wheels must touch the ground. the seat simultaneously and lift the seat off
Do NOT start by lifting the unit/back the seat arms. The child should not be in the
wheels to fold them in. (See Figure 1). seat during this procedure.
2. Push bottom part (B) of the handle
on the spine UP, then – while holding Adjusting the seat height (8)
this – press the top part (A) of handle in Release the handle (F), move the seat arm
– and at the same time – lift this handle to the desired height and lock the handle by
UP. (See Figure 2) pressing it back into place. Please make sure
3. Now, push with your foot on the that you always hold the seat arm by the
lower part of footpeddle (C) located at centre sleeve that attaches it to the centre
top of the arch. Continue to push with column, the seat arm will then be easy to
your foot, while pulling the steering han- move. Adjustable height is 50 to 70 cm from
dle towards you. (See Figure 3) the bottom of the seat.
Unfolding (2) Mounting and adjusting the foot rest (9)
STOKKE® XPLORY® back wheels:
Place the footrest in the tracks. Enable the
Pull the bottom part (B) of the handle adjustment by pulling the white handle. Hold
on the spine UP, then – while holding the white handle activated while moving the
this in position – press the top part foot rest in the tracks. Release the handle
(A) of the handle in – and at the same when the footrest is in the desired position.
time – lift the main steering handle UP There are three footrest positions. Make
and forward. The legs will release. (See sure the footrest is locked in one of the three
Figure 2) positions. Adjust the footrest to support your
If the unit's wheels are locked in a child's feet.
folded position and difficult to release,
give the foot-peddle a slight push – with Seat rail (10)
either your hand or foot - while you Release seat rail on both sides and pull the
unfold the back wheels. rail up. Insert the seat rail into place. A click
will be heard when the rail is placed correctly.
Adjusting the handle, height and Warning! Do not use the rail for carrying.
angle (4)
Lift the trigger (D) and hold it up while Brake (11)
you adjust the handle to the desired
Always remember to engage the brakes when
height. The handle height can be adjust- you park the stroller. Do this by pressing the
ed to any position in a range between lower part of the brake pedal. To release
67 and 116 cm/26,4 and 45,7 inch. The the brake, press the upper part of the brake
handle can be adjusted to 4 different pedal.
angles by pressing the trigger (E) down
and rotating the handle. Removing and attaching
the back wheels (12)
Seat Assembly (5) Release the locking device and pull the wheel
Push the seat down on the seat arm off the axle. To attach push the wheel onto
until a click is heard on each side. The the axle until you hear a click. Check to make
seat may be mounted in a position fac- sure that the wheel is locked on to the axle.
ing forwards or backwards. Check that
the seat is properly mounted on the seat Use on stairs (13)
arms by Stokke Xplory's unique design enables it to
ensuring that the indicators found on negotate obstacles such as thresholds and
each side of the seat have changed col- kerbs with ease. Stokke Xplory is especially
our from red to green.
easy to transport up/down stairs using the
two-wheel function. The child must not be
Adjusting the seat angle (6) sitting in the stroller while it is going up/
The seat angle is adjusted by means of down stairs because transporting a child in a
the handle (G) on the seat arm. Note! stroller on stairs is generally dangerous.
Always keep your hand on the seat
when you adjust the angle. The seat Baby insert (14)
has 3 positions facing backwards, and 2 To ensure the best possible sitting
positions facing forward. comfort for your child make sure that the
depth of the seat corresponds to the length
WARNING! of the child's thigh. The edge of the seat
Never assemble, remove or turn the should fit to the back of the child's knee. The
seat while your child is in it. padded baby insert is attached by putting the
safety harness through the opening that best
fits the child's shoulder height. The baby
insert is recommended up to the age of about
15 months.
Stokke ® Xplory ®
Assemble hood on seat (15)
Position and push the hood plastic fasten-
ers in on each side of the seat. Attach the
hood to the seat fabric with the zipper.
Attach the push buttons on each side.
Dismounting hood from seat (16)
Unbutton on each side of the hood.
Unzip to release the hood. Release plastic
fasteners from seat by pressing the two
taps on the inside of the seat. Use both
tombs and press.
Hood visor (17)
Attach and detach the visor from the
hood with the zip. Fold in and out.
Ventilation in hot weather (18)
Unzip the zip on the hood. Fold the cover
over the edge.
Adjusting the harness (19)
Your child should always use the
harness. Tighten the harness straps so
that the harness fits your child. The har-
ness is opened by pressing the release
mechanisms together. As the child grows,
adjust the harness fasteners at the back
so that they correspond to the child's
shoulder height, see table. Thread the
strap through the fabric parts again.
STOKKE is not responsible if you choose
to use a harness other than the one sup-
plied! Nonetheless there are D-rings on
the waist belt for fitting your own har-
ness.
WARNING
Always use the crotch strap in combina-
tion with the waist belt.
Disassembling the fabric
components for washing:
Disassembling the hood (20)
Unzip to release the hood. Unbutton on
each side of the hood. Pull up the
fabric on the side and the front to reveal
the hood fastener. Press the notch on
the hood fastener and pull up the hood.
Repeat at the other side. Remove the
main rib before washing.
Disassembling the back cover (21)
Loosen the fabric from the push
buttons on each side and from the two in
front. Pull the fabric off the Velcro.
Disassembling the fabric on the
seat guard (22)
Release the rib by pressing a thin pin or
screwdriver into the little hole on each
side. Open textile tab and unzip. Loosen
the fabric from the hook on both side of
the rib.
Disassembling Seat rail cover
Remove by pulling off.
Disassembling Harness covering MAINTENANCE – WASHING
Remove by pulling off. INSTRUCTIONS
Disassembling Seat cover (23) Hard parts
Loosen the orange tag on each side of The stroller should be cleaned using a mild
the bottom rear of the back. Remove the mixture of soap and water. Make sure that
safety harness. Gently pull the seat fabric any sand/mud/grit is removed prior to clean-
up until it is completely off. ing. No part of the stroller is to be lubricated.
If any function of the stroller is not working
properly, contact your
nearest STOKKE retailer.
Textiles must be washed separately (24)
• When washing the baby insert, please
remove the inside cushion before washing
the cover.
• Remove the ribs before washing the
canopy. Release the main rib by pressing,
e.g., a screwdriver into the small holes in the
canopy
fasteners. Afterwards, thread all the ribs out
of the fabric, see page 20.
• For fitting textiles, see pages 18 and 19.
Assembling the fabric components after
washing:
Assembling the Seat cover (25)
Insert the rails on the seat cover into the
slot on each side. Pull the seat cover down.
Position the harness. Crotch, waist and
shoulder straps. Make sure that shoulder
straps correspond to the child's shoulder
height. Fasten the orange tag on each side of
the bottom rear of the back. Conceal the end
of the orange tag in the seat. Pull the fabric
over the back.
Assembling the fabric on the seat guard
(26)
Release the rib by pressing a thin pin or
screwdriver into the little hole on each side.
Fasten the beginning of the zipper around
the bar with Velcro
facing out. Make sure that the tap goes
through the fabric. Pull up the zip with tap
through center and end. Fasten the rib by
pressing it into place.
Note! The rib can be mounted wrong!
Assembling the back cover (27)
Line up the center mark on the fabric to
the corresponding center mark on the seat
guard. Attach the cover edge-to-edge on
the Velcro. Attach the cover with the push
buttons, 2 on each side, and with the two on
each side of the front.
Assembling the hood (28)
Insert the main rib after washing. Make sure
the notch on the main rib is facing front.
Insert the main rib into both sides of the hood
fastener. A click will be heard when the rib is
placed correctly. Fasten the hood with the
push buttons on each side. Zip the hood onto
the seat fabric.
Stokke ® Xplory ®
Assembling the harness covering
Enter the harness covering with the soft
side facing the child.
Assembling the seat rail cover
Enter the cover by pulling it on.
Basic mosquito net (29)
Pull the mosquito net over the handle
and the footrest. Pull the mosquito net
over the main rib of the hood. Snap on
the mosquito net using the push buttons
on each side. Pull the net until the seat is
completely covered. Pull up the zippers
on each side of the central bar.
Basic rain cover(30)
Pull the rain cover over the handle and
the footrest. Pull the rain cover over the
hood. Fasten using the Velcro around the
central bar and footrest. Pull up the zip-
pers on each side of the central bar.
Basic shopping bag(31)
Place the shopping bag on the board.
Fasten around the central bar using the
attached hook.
Changing bag
Attach the changing bag to the seat arm.
Stokke ® Warranty card / Product
registration card:
See description of where to find the
products serial number/date clock on
your product. Use this information when
filling out the Stokke warranty card /
Product registration card. We recom-
mend that you fill in this information at
www.stokke.com.
39