Installation Precautions - Panasonic WV-CW970 Bedienungsanleitung

Consumables
Parts having contacts such as the lens-drive motors,
cooling fan motor and slip-rings inside the camera are
subject to wear with time. Contact the nearest service
dealer about replacement and maintenance of such
parts.
Cleaning the camera
Turn off the camera and wipe it with a soft cloth. If the
camera is very dirty, wipe it off gently with a soft cloth
moistened with a weak solution of water and a neutral
kitchen detergent. Wring all excess liquid from the
cloth before wiping the camera. Next, wipe off all
remaining solution with a soft, dry cloth.
Contact a qualified service person before cleaning the
lenses. (Lenses do not move during cleaning.)
A dirty dome cover or lens causes deterioration of
picture quality. Use lens cleaning paper (like the type
available for cleaning eyeglasses or a camera lens) to
clean the lens.
The dome cover is particularly susceptible to damage.
Gently wipe it with a soft cloth.
Downloading (saving) or uploading (recovering)
camera setting information
Camera setting information that can be downloaded to
the system controller etc, includes existing preset
position settings and menu settings. However, the
following items are not included.
• Patrol function (page 37)
• Area title function (page 39)
• Blemish compensation pattern (page 47)
• RS485 settings (page 20)
• Password settings (page 50)
Be sure the camera is not moving and aimed at
something that moves very little (like a wall) before
downloading camera preset data to the system
controller etc. or uploading downloaded data to the
camera.
Uploading of WV-CW970 series preset data to other
models (e.g. WV-CW860, WV-CW860A) may cause an
error and failure of the uploading process.
Self-diagnosing Function
If abnormal operation due to external noise or some
other reason continues for more than 30 seconds, the
camera will automatically reset itself and restore
normal operation. Reset
initialisation routine that is performed when the camera
is turned on. If the reset is required too often, it could
mean that the camera is installed in a location where
there is a large amount of external noise. This can
cause malfunction of the camera, so you should
contact a qualified service person or system installer
as soon as possible.
Combining devices
There is a limit to the number of devices that can be
put together in one
specifications and outer dimensions before hooking up
the devices. For more information, see the "Panasonic
CCTV System Catalogue" or consult your retailer.
operation the same
configuration. Check

Installation precautions

Be sure to perform installation work in accor-
dance with proper technical standards for electric
installation.
Camera Installation Location
Discuss the installation location for the camera with
your retailer, and select a wall, ceiling or other location
that is strong enough to support the installation.
About ceiling mounts and brackets
For wall mounting, use the optionally available (WV-
Q122) Wall Mount Bracket.
Bolts for mounting the ceiling mount Attachment Pipe
to a ceiling or wall are not provided.
You need to purchase them separately in accordance
with the materials and strength of the place you are
installing the camera.
• Check the installation surface, and the anchors and
bolts to be used for sufficient strength.
• Gypsum board and wood surfaces tend to be
weak, and should not be used as an installation
surface. If use of such a surface for installation is
unavoidable, be sure to take adequate measures to
reinforce the surface.
Tightening the Screws
• Screws should
accordance with the materials and structure of the
installation location.
• Do not use an impact driver to drive screws. Doing
so can damage the screws.
• Drive the screws as straight as possible. After
tightening the screws, visually inspect them to
make sure there is no unevenness and that each
screw is tight.
This camera is designed for use in a hanging con-
figuration only. Using it in an upright or inclined
configuration can cause malfunction and shorten
the life of the camera.
Install the camera in a horizontal configuration,
with the dome pointed downwards.
Be sure to remove this apparatus if it is not in use.
Never install or use the camera in the following
locations.
• Near a swimming pool or other areas where
chemicals are used
• Food preparation areas and other locations where
there are large amounts of steam vapour and oil, in
flammable atmospheres, other special environments
• Areas where radiation, X-rays, strong electric
waves, or magnetism is generated
• At sea, in coastal areas, or in areas where corrosive
the
gas is being generated
• Areas outside of the allowable ambient operating
temperature range (-40 °C to +50 °C)
-8-
be tightened sufficiently in