Adjusting The Carburetor (Idle Speed); Checking The Gearbox Oil Level; Refilling Gearbox Oil; Cleaning - ATIKA ELB 52 Originalbetriebsanleitung
Vorschau ausblenden
Andere Handbücher für ELB 52:
- Originalbetriebsanleitung (170 Seiten) ,
- Montage- und bedienungsblatt (6 Seiten) ,
- Montage- und bedienungsblatt (6 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
If there is no spark visible between the electrodes, the
spark plug may be defective.
S
i
l
e
n
c
e
r
/
e
x
h
a
u
s
t
o
u
t
l
e
t
S
i
l
e
n
c
e
r
/
e
x
h
a
u
s
t
o
u
t
l
e
t
Check the silencer (19) on a regular basis
Clean the exhaust outlet (37) on a regular basis.
Do not clean the silencer when the engine is hot. Dan-
ger of burning!
A
d
j
u
s
t
i
n
g
t
h
e
c
a
r
b
u
r
e
t
o
r
(
A
d
j
u
s
t
i
n
g
t
h
e
c
a
r
b
u
r
e
t
o
r
(
The carburetor is factory-set to the correct idle speed so that
the correct fuel-air mixture is fed to the engine.
In the cases below the carburetor (idle speed) has to be
corrected:
- Speed too high (auger drill continues to move in idle speed)
- Erratic running or lack of acceleration (idle speed too low)
- Adjustment to weather conditions and temperatures
An incorrect carburetor adjustment results in
severe engine damages. Do not continue working
with the machine in such a condition.
Contact a specialist workshop and have the
carburetor adjustment done.
C
h
e
c
k
i
n
g
t
h
e
g
e
a
r
b
o
x
o
i
l
C
h
e
c
k
i
n
g
t
h
e
g
e
a
r
b
o
x
o
i
l
To check the oil level:
Place the earth auger vertically (work position).
Check the oil level at the inspection window (38). Make
sure that the oil level is as shown in the figure:
Refilling gearbox oil
Remove the venting valve (5).
Top up oil until the perfect / max. filling level is reached (do not
overfill). Use GL 85 W gearbox oil.
Re-install the venting valve (5) and tighten it.
C
l
e
a
n
i
n
g
C
l
e
a
n
i
n
g
Clean the machine and its accessories thouroughly after
each application so that the faultless function is kept.
Clean all movable parts on a regular basis.
i
d
l
e
s
p
e
e
d
)
i
d
l
e
s
p
e
e
d
)
l
e
v
e
l
/
r
e
f
i
l
l
i
n
g
g
e
a
r
b
o
x
o
i
l
e
v
e
l
/
r
e
f
i
l
l
i
n
g
g
e
a
r
b
o
x
o
i
Clean the case with a soft brush or a dry cloth.
Do not clean the machine under running water or using a
high-pressure cleaner.
Do not use solvents (gasoline, alcohol, etc.) for plastic parts,
otherwise such parts may be damaged.
Keep the handles free of oil and grease.
Water, solvents and polishing agents shall not be
applied.
cooling are free (risk of overheating).
Keep also the cooling fins for the cylinder (j) free from
dust and dirt.
Before each transport
Switch off device.
Wait until the cutting device does not longer
Allow the machine to cool down.
Close vent valve.
Carry the product with the handle.
When transporting the product within a car put it in the boot
or on a separate loading area. Secure the machine against
tipping over, damages and fuel spillage.
l
l
Keep unused machines in a dry and closed area out of the
reach of children. Do not store them close to a cooker, oven
or hot-water apparatus with permanent flame or other spark-
generating devices.
Allow the engine to cool down before storing the machine.
Close the vent valve to prevent gear oil from escaping.
Before extended storage, please observe the following to
increase the service life of the device and to ensure smooth
operation:
Thoroughly clean the device.
Oil all moving parts with environmentally compatible oil.
Empty the fuel tank completely.
compatible manner.
Operate the engine until the carburetor is empty.
Check the machine for perfect condition to ensure a safe
use of it after a longer period of storage.
Make sure that the ventilation slots (i) for the engine
T
r
a
n
s
p
o
r
t
T
r
a
n
s
p
o
r
t
move.
S
t
o
r
a
g
e
S
t
o
r
a
g
e
Do not use grease.
Dispose of remaining fuel in an environmentally
21
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
