Werbung
Verfügbare Sprachen
Verfügbare Sprachen
deu
6. Hersteller-Garantie
Die Garantiezeit beträgt 12 Monate nach Übergabe des Neuproduktes
an den Erstverwender, höchstens jedoch 24 Monate nach Auslieferung
an den Händler. Der Zeitpunkt der Übergabe ist durch die Einsendung
der Original-Kaufunterlagen nachzuweisen, welche die Angaben des Kauf-
datums und der Produktbezeichnung enthalten müssen. Alle innerhalb
der Garantiezeit auftretenden Funktionsfehler, die nachweisbar auf Fer-
tigungs- oder Materialfehler zurückzuführen sind, werden kostenlos be-
seitigt. Durch die Mängelbeseitigung wird die Garantiezeit für das Produkt
weder verlängert noch erneuert. Schäden, die auf natürliche Abnutzung,
unsachgemäße Behandlung oder Missbrauch, Missachtung von Be-
triebsvorschriften, ungeeignete Betriebsmittel, übermäßige Beanspru-
chung, zweckfremde Verwendung, eigene oder fremde Eingriffe oder an-
dere Gründe, die BERNER nicht zu vertreten hat, zurückzuführen sind,
sind von der Garantie ausgeschlossen.
Garantieleistungen dürfen nur von einer autorisierten BERNER Vertrags-
Kundendienstwerkstatt erbracht werden. Beanstandungen werden nur
anerkannt, wenn das Produkt ohne vorherige Eingriffe in unzerlegtem Zu-
stand einer autorisierten BERNER Vertrags-Kundendienstwerkstatt ein-
gereicht wird. Ersetzte Produkte und Teile gehen in das Eigentum von
BERNER über.
Die Kosten für die Hin- und Rückfracht trägt der Verwender.
Die gesetzlichen Rechte des Verwenders, insbesondere seine Mänge-
lansprüche gegenüber dem Händler, bleiben unberührt. Diese Hersteller-
Garantie gilt nur für Neuprodukte, welche in der Europäischen Union, in
Norwegen oder in der Schweiz gekauft werden.
For use of the BERNER pressing tongs for the various pipe connection sy-
stems, the currently valid BERNER sales documents are applicable. If the
system manufacturer alters components of pipe connection systems or mar-
kets new ones, their current application status must be enquired about at
BERNER (Fax +49 7940 121-300). Subject to modification without notice,
errors and omissions excepted.
Figs. 1–2
1
Pressing tongs
2
Tong retaining bolt
3
Pressure plate
4
Locking pin
5
Press rollers
6
Housing grip
General Safety Rules
WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term „power tool" in
all of the warnings listed below refers to your mains operated (corded) power
tool or battery operated (cordless) power tool, also machines and electric units.
Only use the power tool for the purpose for which it was intended, with the due
attention to the general safety and accident prevention regulations.
To reduce the risk of injury, user must read and understand instruction
manual.
SAVE THESE INSTRUCTIONS.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite acci-
dents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Dis -
tractions can cause you to lose control.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock. If
the power tool comes with an earthed wire, the plug may only be connected
to an earthed receptacle. At work sites, in damp surroundings, in the open
or in the case of comparable types of use, only operate the power tool off
the mains using a 30 mA fault current protected switch (FI breaker).
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or un -
plugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of elec-
tric shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
C) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of in -
attention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position be-
fore plugging in. Carrying power tools with your finger on the switch or
plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
eng
8 Inching switch
9 Pistol grip
10 Pressing jaw
11 Pressing contour
12 Bolt
13 Reset button
Werbung
