Hürner HST 300 Print+ 2.0 Bedienungsanleitung Seite 31

H Ü R N E R S c h w e i s s t e c h n i k G m b H
Nieder-Ohmener Str. 26
35325 Mücke, Germany
unit or pressing the STOP/RESET key will reset the unit back to the
start of entering the welding parameters.
5.12 Using ViewWeld to Manage Logged Welding Reports, Print
Tags, and Assign Geo-data
The ViewWeld feature offers viewing an abstracted version of the
welding reports recorded during the welding processes and printing
it as a label tag to be affixed to the joint on the optionally available
tag printer. The ViewWeld abstract shows the report number, the date
and time of the welding and the welding parameters along with an
evaluation of the quality of the joint/welding operation (see Display 6),
where the first displayed abstract is that of the last performed weld-
ing operation.
To call the ViewWeld abstract of a welding report, press the ñ key in
the bar code input screen (see Display 2). Browsing through the saved
welding reports is then possible by pressing the ï or ð cursor keys. To
print a tag of the welding operation of which the abstract is currently
displayed, the label tag printer has to be connected to the welder.
Then press the START/SET key in the ViewWeld screen.
ViewWeld also enables assigning the geo-data of a joint after it was
made, in case they were not recorded with enabled geo-data logging
at the welding operation (see Sect. 6.7). To do this, call the ViewWeld
screen and, if needed, browse to the welding abstract of the joint that
needs to have its geo-data assigned. Then press the ñ cursor key in
the ViewWeld screen displaying the desired welding operation. This
causes a screen asking you if you want to record geo-data to appear
(see Display 12). Confirm by pressing the START/SET key and log the
geo-data according to the procedure described in Sect. 6.7.
6 Additional Information in the Welding Report
Every welding report saved to system memory, which can be down-
loaded as a PDF report file or in the DataWork format, contains a
number of welding and traceability data that the operator can decide
to enter or not to enter in the set-up menu.
6.1 Entering Preformatted and User-defined Traceability Data
All traceability data enabled in the configuration menu at "Data
Recording" (see Sect. 10) have to be entered before the welding pro-
cess. The welding unit prompts the user to enter them either before
or after entering the fitting bar code (see Display 2). Depending on
what data is entered, either its repeated input is mandatory (e. g.,
the welder ID code; see Sect. 5.2) or previously entered data can be
changed and confirmed or confirmed without changes (e. g. the com-
mission number; see Sect. 6.2).
Certain traceability data can also be accessed quickly, via a selection
screen, by pressing the ï cursor key (see Display 7), either for view-
ing or for entering or changing/confirming them (for the AutoWeld
feature mentioned along with them on this screen, see Sect. 5.5).
6.2 Entering or Changing the Job Number and Joint Number
The commission number input screen is shown by the unit before weld-
ing or accessed by the user in the quick access screen (Display 7). It can
be entered using the alphanumeric keypad (see Info in Sect. 5.2) or by
reading it from a bar code using the scanner. The maximum length is
32 characters. Confirm your input by pressing the START/SET key. The
Version August 2014 HÜRNER HST 300 Print + 2.0 User's Manual
0015 24.02.13 09:33
M/B MON HST 315
0058s 025.0V 1.57Ω
No Error
Display 6
*** Recording ****
AutoWeld
>Welder ID Code
Enter Job No.
Display 7
Enter Job No.
********************
************
Display 8
EN
11