Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PLOW ACCESSORIES AND ENHANCEMENTS
1.
Plastic Wear Bar an ultra high molecular
weight plastic bar that replaces the steel bar.
This bar prevents wear of the blade and will
minimize plow scraping on concrete or brick
surfaces.
2.
Blade Side Wall controls run off of
material as it is piled in front of blade. The
heavy duty steel construction will prevent
material from escaping and better allow you
to move the material off to one side.
3.
Snow Control Flap is a flexible rubber
flap that bolts to the top of the plow blade.
This accessory keeps the snow (or light
material) from flowing up over the blade,
keeping the snow in front of the blade out of
the operator's vision.
4.
Plow Lift or Winch are methods for
lifting the plow. Unlike the Winch, the Plow
Lift is specifically designed to lift the plow
blade and does not use a rope.
5.
Plow Lift Rope is a durable, synthetic
rope that replaces the winch rope. This rope
stands up to the repeated sharp angle pulls
used to lift a heavy plow blade. Use this rope
with the Plow Roller Fairlead for maximum
rope life.
4.
3.
2.
1.
6.
Roller Fairlead for Plow Lifting
designed for use with Warn winches that
raise and lower the plow blade. The larger
diameter lower roller reduces wear of the
rope.
7.
Power -Pivot replaces the pivot latching
system on the plow. This heavy duty electric
device will pivot the plow blade in either
direction with the push of a button. It is
powerful enough to rotate your blade while
plowing. Plow loads are transmitted to the
base though an electric over hydraulic system.
This accessory greatly improves productivity.
8.
Plow Markers clearly mark the corners
of your blade. These markers are flexible and
two feet high to improve plow visibility when
plowing close to objects in deep snow.
5.
6.
7.
WARN INDUSTRIES
7
HOW THE PLOW WORKS
WARNING
Always check the winch for back-driving
and nesting before plowing. Failure to do so may cause
the plow to creep downward when in the up position. If
the plow creeps down low enough, the blade may hit a
stationary object ejecting the rider from the vehicle and
causing serious injury or death.
WARNING
Always check lift mechanism, straps or
winch rope integrity before plowing. Failure to do so may
cause the plow to drop suddenly from the up position and
impact a low-lying object, potentially ejecting the rider
from the vehicle and causing serious injury or death.
Plow Mechanics
Now that you are familiar with your
WARN plow and its components, we can
begin reviewing how it works. The plow wear
bar contacts the surface to be plowed and
scrapes the material from the surface. The
material is then pushed into the blade by the
material on the plow surface and slides along
the moldboard. The material rolls over and
falls on top of the material in front of the plow
as it reaches the top of the moldboard.
he t
When the blade is set at a pivot angle, the
blade is set at a pivot an
plowed material will roll over and flow to
erial will roll over and flow
the side of the vehicle, leaving the
he vehicle, leaving the
area plowed.
.
As the material rolls over in
terial rolls over in
front of the plow blade it
plow blade it
will become deeper. The
deeper. The
deeper the material the
mat
ater
harder the vehicle will
ehic
need to work to move the
k to move the
to m
material. If the material
he material
e ma
is too deep or the
or the
vehicle has no
no
traction, the
plow will not
t
be effective as
as
as
s
the material
will not be
able to roll over
over
er
in front of the blade.
e blade.
8.
The blade attack angle can be
attack ang
adjusted and will change the blade cutting
d will change the blade cutting
action. Generally, the blade should be set
with the top lip in the back position.
p in the back position.
p in the back position.
The plow skids may be used to control
how deep the blade will cut into the material
on the plow surface. The skids may be set
to raise the wear bar the maximum distance
off the surface. The area may be plowed to
s along
r and
m
ri
n
fro
fr
t
the plow
t
p
w
op
t
m
l
db
bo
rd
d.
e
e is
s set
s s
t a
a
v
a
ng
ng
gle, the
e h
ill r
ll rol
roll ov
rol
ov
er
nd
ow
w to
w
v
cle
cle, le
e
eav
v
ng
e
r
ov
ov
ver in
ve
in
ade
t
t
eper. Th
per. T
The
T
Th
he
he
h
he
ter
er
er
r
rial the
he
he
c will
cle
e
e will
will
m
move t
ov
ve t
r
blad
blad
e .
e
.
tt
ttac
an
ngle can be
gle can be
b
ch
ch
h
han
h
hang
ange the blade cu
nge the blade cu
e the bla
b
ng
ng
y, the blade should be
y
, the blade sho
th
the blade shoul
the blade should be
set
et
e
in the back position.
WARN INDUSTRIES
8
remove
remove the top layer of
mater
material. A second pass
may
may be made with the plow
y
skid
skids in a raised position
ds
d
a
that will allow the blade
th
h
at
t t
t t
to remove all material
o remo
o r
o remove
r
re
em
down to the ground
down to
down
do
ow
surfa
surface
surface. Operating
with the plow skids
with t
at ma
at maximum position
m
m
may be optimal when
may b
gradin
g
grading material
onto t
onto the surface or
when
when trying to keep
the wear bar from
the we
damaging the surface.
damagi
Werbung
