Inhaltsverzeichnis
Werbung
Montageanleitung ECblue BASIC-MODBUS, ECblue BASIC
Labeling Requirements
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met.
This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate
Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC
ID: T7V1740. This FCC identifier is valid for all PAN1740 modules.
In any case the end product must be labelled exterior with "Contains FCC ID: T7V1740"
Antenna Warning
For the related part number of PAN1740.
This device is tested with a standard SMA connector and with the antennas listed below. When
integrated in the OEMs product, these fixed antennas require installation preventing end-users from
replacing them with non-approved antennas. Any antenna not in the following table must be tested to
comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions.
Item
Part Number
1
LDA212G3110K
RF Exposure
The radiated output power of PAN1740 with mounted ceramic antenna (FCC ID: T7V1740) is far
below the FCC radio frequency exposure limits.
Nevertheless, the PAN1740 shall be used in such a manner that the potential for human contact
during normal operation is minimized
1.7.3
Industry Canada Certification @ AM-MODBUS-WB, AM-STICK-WB
This device contains "Contains IC: 216Q-1740".
PAN1740 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-
1740.
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any
regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain
Canadian information on RF exposure and compliance from www.ic.gc.ca.
This device has been designed to operate with the antennas listed in the Table above, having a
maximum gain of 0.9 dBi. Antennas not included in this list or having a gain greater than 0.9 dBi are
strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna
used for this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Due to the model size the IC identifier is displayed in the installation instruction only and can not be
displayed on the modules label due to the limited size (8.7x15.6 mm).
IC Notice
The devices contains "Contains IC: 216Q-1740", including the antennas, which are listed in above,
complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter
approval as detailed in RSS-GEN.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause unde-
sired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et.
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
PAN1740 est garanti conforme aux dispositions règlementaires d'Industry Canada (IC), licences: IC:
216Q-1740 Il est recommandé aux fabricants d'appareils fixes, mobiles ou portables de consulter la
réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites
d'exposition aux rayonnements radiofréquence ainsi qu'au débit d'absorption spécifique maximum
autorisé.
L-BAL-F079D-D 2023/24 Index 003
Manufacturer
Frequency Band
Murata
2.4 GHz
Art.-Nr.
8/84
Allgemeine Hinweise
Type
Gain (dBi)
Chip-Antenna
+0.9
Werbung
Inhaltsverzeichnis
