Delta SOLIVIA 11 EU G4 TR Betriebsanleitung Seite 35

5. Select Continue and press the E
I n s t a l l a t i o n
L a n g u a g e : E n g l i s h
C o n t i n u e
➔
- - - - - - - - - - - - - - - - - - -
→ The menu Load USB data menu is displayed.
6. In the Load USB data menu, select the option Yes to
load data from the USB.
L o a d U S B d a t a
- - - - - - - - - - - - - - - - - - -
Y e s
➔
N o
→ The next Load USB data menu is displayed.
7. In the Load USB data menu, select the Load settings
option.
L o a d U S B d a t a
L o a d s e t t i n g s
➔
L o a d s w a p d a t a
→ The next Load USB data menu is displayed.
8. Insert the USB stick into the USB socket underneath
the solar power inverter and press the E
L o a d U S B d a t a
I n s e r t U S B s t i c k
a n d p r e s s E N T E R
→ The Select RS485 ID menu is displayed.
9. Select the RS485 ID of the solar power inverter from
which the data is to be loaded.
S e l e c t R S 4 8 5 I D
I D :
➔
C o n t i n u e
10. Select Continue and press the E
→ Loading of the data begins.
A message is displayed when the loading process
is successful.
L o a d d a t a
S u c c e s s f u l
P r e s s E N T E R
11. Press the E button.
ntEr
→ The Edit Loaded Data menu is displayed.
12. Select No and press the E
E d i t L o a d e d D a t a
N o
➔
Y e s
→ The Date and time menu is displayed.
Operation and installation manual for SOLIVIA 11 EU G4 TR
button.
ntEr
button.
ntEr
_ _ _
button.
ntEr
button.
ntEr
_ _ _
NOTE
If a power limit was set at the solar
power inverter from which the data
was loaded, the following message
appears:
T h e p o w e r o f t h e
i n v e r t e r i s
l i m i t e d t o :
► If you set a power limit then you
must also fill out the label stating
"The power of the product has been
reduced ..." and apply this label to
the front of the solar power inverter.
Use a waterproof pen for filling out
this information.
NOTE
► Select Yes if you wish to edit the
loaded data. Commissioning then
proceeds in the same manner as
the standard commissioning pro-
cedure (depending on the selected
grid). The loaded data is then
shown in the individual menus and
not the default values.
13. Set the date and time.
D a t e a n d t i m e
C o n t i n u e
D a t e : _ _ : _ _ : _ _ _ _
➔
T i m e : _ _ : _ _ : _ _ p m
14. Select Continue and press the E
→ The RS485 menu is displayed.
15. Set the RS485 ID and the baud rate.
R S 4 8 5
C o n t i n u e
I D :
➔
B a u d r a t e : 1 9 2 0 0
Configurable parameters
Display text Designation
ID
RS485 ID
Baudrate
Baud rate
Termination:
Termination resis-
tor
8. Commissioning
_ _ _ _ W
button.
ntEr
1
Description
1 .. 255
2400 | 4800 | 9600 |
19200 | 38400, the
standard is 19200
ON | OFF
31
EN