Before Starting The Equipment; Attachment And Operation - Parkside MPKZ 2000 A1 Originalbetriebsanleitung

8. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
m DANGER
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a base frame with 4
screws (not included in delivery) using the holes on the fixed
saw table (15).
• Pull out the pre-installed tilt protection (36) completely and
secure it with an Allen key (D) (fig. 2).
• Adjust the adjusting screw (37) to the level of the tabletop to
avoid wobbling of the machine (fig. 3).
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are dentical to the mains
data.
8.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
8.1.1 Check function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to the saw
blade without touching other parts.
• When folding the saw upwards into the starting position,
the saw blade guard must cover the saw blade automati-
cally.

9. Attachment and operation

9.1 Attaching the multifunction sliding cross cut mi-
tre saw (fig. 1/2/3/4)
• In order to adjust the rotary table (14), fold the locking han-
dle (11) upwards and pull up the latched position lever (35)
with your index finger.
• Turn the rotary table (14) and pointer (12) to the desired
angle measurement of the scale (13). To fix the setting, fold
the locking handle (11) downwards.
8 GB/IE/NI
• Press the machine head (4) lightly downwards and remove
the locking bolt (23) from the motor bracket. Thus, the saw
disengages from the lowest position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) in the holes on the rear side of the stop rail (16) and
secure it with the star grip screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must only be
mounted on the right side (see fig. 12-13).
• It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
• Workpiece supports (8) must always be secured and used
during work. Set the desired table size by loosening the set
screw (9). Then tighten the set screw (9) again.
9.2 Chip collection bag (fig. 1/5)
The saw is equipped with a chip collection bag (17) for saw-
dust and chips.
Attention! The chip collection bag may only be used when
cutting wood and wood-like materials! When cutting metal,
there is a risk that hot chips will ignite the chip collection bag.
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The chip collection bag (17) can be emptied by means of a
zipper at the bottom.
9.2.1 Connection to an external dust extractor
• Connect the extraction hose to the dust extractor of a work-
shop vacuum cleaner.
• The workshop vacuum cleaner must be suitable for the mate-
rial being worked.
Attention! Always observe the safety and warning notices of
the workshop vacuum cleaner being used.
• When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
9.3 Precision adjustment of the stop for crosscut
90° (fig. 1/6/7)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Loosen the set screw (22).
• Position the angle stop (A) between the saw blade (6) and
the rotary table (14).
• Loosen the lock nut (26a).
• Adjust the adjusting screw (26) until the angle between the
saw blade (6) and rotary table (14) is 90°.
• Re-tighten the lock nut (26a).
• Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screwdriv-
er, set to position 0° on the angle scale (18) and re-tighten
the retaining screw.
9.4 Crosscut 90° and turntable 0° (fig. 1/2/8)
In the case of cutting widths up to approx. 100 mm it is possible
to fix the traction function of the saw with the set screw (20) in
the rear position. In this position the machine can be operated
in cross cutting mode. If the cutting width is over 100 mm then
it is necessary to ensure that the set screw (20) is loose and the
machine head (4) can move.