Risk Of Injury; Transport (Fig. 2/3) - Parkside MPKZ 2000 A1 Originalbetriebsanleitung

9.8 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/8/10)
The multifunction sliding cross cut mitre saw can be used to
make mitre cuts to the left of 0°- 45° in relation to the work
face and, at the same time, 0° - 45° to the left or 0° - 45° to
the right in relation to the stop rail (double mitre cut).
Attention! For 0°- 45° mitre cuts, the clamping device (7)
must only be mounted on the right side (see fig. 12-13).
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be locked so that the dis-
tance between the stop rail (16a) and the saw blade (6) is
at least 8 mm.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Fold the locking handle (11) upwards to loosen the rotary
table (14) (fig. 3+4).
• Set the rotary table (14) to the desired angle (refer also to
point 9.5 in this regard).
• Fold the locking handle (11) downwards to secure the rotary
table (14) (fig. 3+4).
• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 9.7).
• Re-tighten the set screw (22).
• Cut as described under section 9.4.
9.9 Limiting the cutting depth (fig. 14)
• The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).
• Check the setting by completing a test cut.
9.10 Changing the saw blade (fig. 2, 15-17)
Remove the power plug!
Attention!
Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and lock with the lock-
ing bolt (23).
• Use one hand to insert the Allen key (C) in the flange screw
(28).
• Firmly press the saw shaft lock (30) and slowly rotate the
flange screw (28) in clockwise direction. The saw shaft lock
(30) engages after no more than one rotation.
• Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
• Turn the flange screw (28) right out and remove the outer
flange (29).
• Fold the saw blade guard (5) upwards.
• Take the blade (6) off the inner flange (31) and pull out
downwards.
• Carefully clean the flange screw (28), outer flange (29) and
inner flange (31).
10 GB/IE/NI
• Fit and fasten the new saw blade (6) in reverse order.
• Attention! The cutting angle of the teeth, in other words
the direction of rotation of the saw blade (6) must coincide
with the direction of the arrow on the housing.
• Before continuing your work make sure that all safety de-
vices are in good working condition.
• Attention! Every time that you change the saw blade (6),
check to see that it spins freely in the table insert (10, fig. 1)
in both perpendicular and 45° angle settings.
• Attention! The work to change and align the saw blade
(6) must be carried out correctly.
9.11 Using the laser / LED (fig. 18)
Function
OFF
9.12 Adjusting the laser (fig. 19)
If the laser (32) ceases to indicate the correct cutting line, you
can readjust the laser. Loosen the Philips head screws (E) and
set the laser by moving sideways until the laser beam strikes the
teeth of the saw blade (6).
Firmly secure both screws (E).
9.13 Changing the speed (fig. 18)
The mitre saw has 2 speed ranges:
• To operate the mitre saw at a speed of 3200 rpm (metal), set
the speed regulation switch (34) to position I.
• To operate the saw at a speed of 5000 rpm (wood), set the
speed regulation switch (34) to position II.

10. Transport (fig. 2/3)

• Tighten the locking handle (11) to lock the rotary table.
• Press the machine head (4) downwards and secure with the
locking bolt (23).
• Fix the saw's drag function with the locking screw for drag
guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as described
under section 8.
Press the ON/OFF switch
laser/LED (33)
1x
1x
1x.
1x