With The Drag Guide (21) Not Fixed In Place - Parkside MPKZ 2000 A1 Originalbetriebsanleitung

Attention! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
• The moveable stop rail (16a) must be locked so that the dis-
tance between the stop rail (16a) and the saw blade (6) is
no more than 8 mm.
• Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Use the handle (1) to push back the machine head (4) and
fix it in this position if required (dependent on the cutting
width).
• Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
• Lock the material with the clamping devices (7) on the fixed
saw table (15) to prevent the material from moving during
the cutting operation.
• Release the lock switch (3) and press the ON/OFF switch
(2) to start the motor. (Refer also to point 9.13 "Changing
the speed" in this regard.)
• With the drag guide (21) fixed in place (21):
use the handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw blade (6)
has completely cut through the work piece.

• With the drag guide (21) not fixed in place (21):

pull the machine head (4) all the way to the front. Lower the
handle (1) to the very bottom by applying steady and light
downward pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (6) has
completely cut through the work piece.
• When the cutting operation is completed, move the machine
head back to its upper (home) position and release the ON/
OFF button (2).
Attention! The machine executes an upward stroke auto-
matically due to the return spring, i.e. do not release the han-
dle (1) after completing the cut; instead allow the machine
head to move upwards slowly whilst applying light counter
pressure.
9.5 Crosscut 90° and turntable 0° - 45°
(fig. 1/8/9)
The multifunction sliding cross cut mitre saw can be used to
make crosscuts of 0° -45° to the left and 0° -45° to the right
in relation to the stop rail.
Attention! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
• The moveable stop rail (16a) must be locked so that the dis-
tance between the stop rail (16a) and the saw blade (6) is
at least 8 mm.
• Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen the locking handle (11) if tightened. Pull up the
latched position lever (35) with your index finger and use
the locking handle (11) to set the rotary table (14) to the
desired angle (fig. 3+4).
• The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
• Re-tighten the locking handle (11) to secure the rotary table (14)
(fig. 3+4).
• Cut as described under section 9.4.
9.6 Precision adjustment of the stop for mitre cut
45° (fig. 1, 7-11)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Fix the rotary table (14) in the 0° position.
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be locked so that the dis-
tance between the stop rail (16a) and the saw blade (6) is
at least 8 mm.
• The moveable stop rail (28) must be fixed in the inner posi-
tion (right side).
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (14).
• Loosen the lock nut (27a) and adjust the adjustment screw
(27) until the angle between the saw blade (6) and the ro-
tary table (14) is precisely 45°.
• Re-tighten the lock nut (27a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 45° on the angle scale (18) and re-tighten
the retaining screw.
9.7 Mitre cut 0°- 45° and turntable 0°
(fig. 1, 7-10)
The multifunction sliding cross cut mitre saw can be used to
make mitre cuts of 0° - 45° in relation to the work face.
Attention! For 0°- 45° mitre cuts, the clamping device (7)
must only be mounted on the right side (see fig. 12-13).
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be locked so that the dis-
tance between the stop rail (16a) and the saw blade (6) is
at least 8 mm.
• The moveable stop rail (28) must be fixed in the inner posi-
tion (right side).
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) to the left, until the pointer (19) indi-
cates the desired angle measurement on the scale (18).
• Re-tighten the set screw (22).
• Cut as described in section 9.4.
GB/IE/NI 9