SILENTRON 5500 SILENYA HT Bedienungsanleitung Seite 92

24 H ROBBERY ↑
↓
↵ CONFIRM ↓
9.1 – REMOTE CONTROLS programming
Up to 32 remote controls can be programmed. Each can operate in all zones or only in certain zones, depending on the programming.
REMOTE CONTROLS ↑
↵ CONFIRM ↓
REM.01 ON A B C ↑
↵ OFF A B C ↓
Select a configuration and confirm: The request to press the red and green remote control buttons together will appear on the display. Once this
is done a short Beep confirms the operation and the display indicates the configuration programmed. When this is confirmed, a name can be
given to the remote control (LABEL). It is advisable to use the name of the owner (max. 9 characters) which will be registered in the events
memory with every operation. When this is confirmed, the VOCAL LABEL is accessed to record the name of the owner of the remote control by
following the same procedure applicable to vocal messages (exit using ESC when recording is correctly completed). This name will be used in
all vocal communications of the control panel. Proceed as indicated above for every remote control, using the arrows to change the number.
Note: The remote controls normally have 4 coloured buttons, 2 of which can automatically partially arm the control panel. See the remote control
instructions for information on these functions, taking into consideration that the programming on the control panel predominates.
Note: If the control panel responds with 3 BEPs during programming of a remote control, it means that it has already been programmed. This
applies to any other device which is to be programmed via the control panel (keypad codes, sensors, detectors).
a) Cancellation of remote controls
This operation can also be performed by the user as follows:
Enter the USER (or INSTALLER) CODE and confirm; search for EXTRAS menu using the
arrows and confirm. The REMOTE CONTROLS menu appears; when this is confirmed the first
free position will be shown (remote control to be programmed). Using the arrows, find the remote control
to be cancelled and confirm. The configuration of the remote control selected appears (see figure).
Press CANC and DELETE? appears.
cancellation of the remote control. The control panel confirms with a Beep.
b) Adding remote controls
The user can also perform this operation as described above up to viewing the first free position available (without the word MEMOR.), then
proceed as for a new programme.
9.2 - Programming of KEYPAD CODES (use exclusively KEYPAD HT – avoid other models)
The 5-digit numeric codes used for total or partial arming or for disarming are programmed directly on the control panel and can be used on all
keypads installed in the system. Codes the same as the user-installer codes cannot be used. The programming of these codes (up to 32 so that
each user can have his/her own) is performed in the CODES menu as follows (when confirming CODES the first free position always appears):
KEYBOARD CODES ↑
↵ CONFIRM ↓
↵ INTROD. COD. 02
SILENTRON – made in Italy
24 H TECHNOL. ↑
↵ CONFIRM ↓
REM. CONTROL 01 ↑
↵
↵ CONFIRM ↓
confirming this configuration
with ↵ the remote control
can arm and disarm everything
Press ↵ to confirm
CODE 02 ↑
↵
↵ CONFIRM ↓
enter 5
INTRO. COD. 02
digits
1 2 3 4 5
↓ WIRED INPUTS ↑
↵ CONFIRM ↓
REM.01 ON A B C ↑
↵
↵ OFF A B C ↓
REM. 01 ON A B C ↑
↵ OFF A ↓
COD. 02 ON A B C ↑
↵
↵ OFF A B C ↓
1 2 3 4 5 ON A B C
MEMOR. OFF A B C
COPYRIGHT SILENTRON DS5500/1/2/3BA080228GM
↓ EXTERNAL KEY ↑
↵ CONFIRM ↓
Use numbers from 1 to 6 to
enable or disable function or
zones required. Example:
confirming this configuration
with ↵ the remote control can
arm everything but disarm only A
REM. 01 ON A B C
MEMOR. OFF A
REM. 01 ON A B C
DELETE ?
Use numbers from 1 to 6 to
enable or disable
functions and ↵ zones required
(see remote controls)
↵
↓
12