8.0 - Vocal Message Recording - Writing Smss - Vocal Event Messages - SILENTRON 5500 SILENYA HT Bedienungsanleitung

SMS MESSAGES
↵ - - - - - -
Once this link has been completed (↵) another display will appear to link the number being
programmed to a further 11 SMSs already programmed at the factory (default). These signal situations of:
anomalies and/or useful control panel functions as listed below.
Note: Linking messages to numbers must be performed for each of the stored telephone numbers. If a number is not linked to a message, no
telephone call will be made to that number since the control panel will not know what to communicate.
b) List of SMSs programmed at the factory:
1 = low control panel battery; Note: this message warns that the system may stop working!
2 = low peripheral device battery; Depending on the model, the detectors can function autonomously for several days (see specific manual).
3 = supervision failure and/or radio noise – the message is sent only if the checking function has been activated (SETTINGS).
4 = control panel armed – the message is sent only as confirmation when the system is armed via external telephone.
5 = control panel disarmed – the message is sent only as confirmation when the system is disarmed via external telephone.
6 = mains failure 230V – the message is sent after a programmable period of continuous power failure (SETTINGS).
7 = No GSM network for over 15 min. - The event is memorised and the message is sent when the GSM network is working again.
8 = No successful call on PSTN line – this message indicates possible disturbances on the telephone line (PSTN line).
9 = Periodic message indicating control panel operating status; every specific number of hours/days (SETTINGS) the system communicates
correct functioning.
10 = SIM card expiry warning; programme (SETTINGS) the next expiry date in the case of a pre-paid SIM card.
11 = Mains 230 V restored; this message does not have to be linked to a number since it is sent to the number linked to message 6.
c) Enabling direct external access
When the numbers and messages have been linked, a request will appear on the display to enable direct access: this option allows you to call
and operate the control panel from a cellular telephone without entering the user code (see 5.2) as the number of the caller is recognised; of
course, this applies only if this number is transmitted.
To enable this function, use the arrows until the "Y" (yes) appears instead of "N".
d) ERASING AND/OR CHANGING PHONE BOOK
In order to change the phone book, search for the number desired (can be done in two ways), then change or erase completely.
PHONE BOOK ↑
↵ CONFIRM ↓
ADD
↵ POSITION 2
ADD
↵ NAME
8.0 – VOCAL MESSAGE RECORDING – WRITING SMSS – VOCAL EVENT MESSAGES
MESSAGES ↑
↵ CONFIRM ↓
The VOCAL MESSAGES menu and SMS MESSAGES menu (only for control panels with GSM module) are used to record/write directly to the
device the 6 alarm messages which will be sent to the linked telephone numbers (see B - events programmed at the factory). These messages
SILENTRON – made in Italy
If the control panel has a GSM module with relative SIM card, a display will appear to link to the number the
SMSs corresponding to the 6 vocal messages described above (to be written by the installer – MESSAGES
menu).
Note: Messages 6, 7 and 11 are not available on the FREE models.
↵
↵ CONFIRM ↓
↵
↵ 2223334567
Philip
↵ ↵ 2223334567
VOCAL MESSAGES ↑
↵
↵ CONFIRM ↓
MEMORY ↑
PHILIP 02
PHILIP 02
COPYRIGHT SILENTRON DS5500/1/2/3BA080228GM
TECHNICAL SMS
↵ - - - - - - - - - - -
DIRECT
↵ ACCESS N
SEARCH
↑
↵ POSITION
← Cancel completely
change with
with CANC
↑
MESSAGES/EVENTS ↑
↵ CONFIRM ↓
SMS MESSAGES ↑
↓
↵ CONFIRM ↓
9