Briggs & Stratton BPW3000 Bedienungsanleitung Seite 6

WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury. Turn pressure washer
engine off and let it cool at least 2 minutes before removing
fuel cap. Loosen cap slowly to relieve pressure in tank. Fill
fuel tank outdoors. DO NOT overfill tank. Allow space for
fuel expansion. If fuel spills, wait until it evaporates before
starting engine. Keep fuel away from sparks, open flames,
pilot lights, heat, and other ignition sources. Check fuel
lines, tank, cap and fittings frequently for cracks or leaks.
Replace if necessary. DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B).
Be careful not to overfill. Allow about 4 cm (1.5") (C) of
tank space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
High Altitude
At altitudes over 1524 m (5,000 ft.), a minimum 85 octane
/ 85 AKI (89 RON) gasoline is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions. See an Authorized Briggs & Stratton dealer
for high altitude adjustment information. Operation of the
engine at altitudes below 762 m (2,500 ft.) with the high
altitude kit is not recommended.
Pressure Washer Location
Carbon Monoxide Poisoning
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in minutes.
You CANNOT smell it, see it, or taste it. Even if you do
not smell exhaust fumes, you could still be exposed to carbon
monoxide gas. Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon monoxide
gas from accumulating and potentially being drawn towards
occupied spaces. Install battery-operated carbon monoxide
alarms or plug-in carbon monoxide alarms with battery back-up
according to the manufacturer's instructions. Smoke alarms
cannot detect carbon monoxide gas. DO NOT run this product
inside homes, garages, basements, crawlspaces, sheds, or other
partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in
these spaces and can linger for hours, even after this product has
shut off. ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces. If you start to feel
sick, dizzy, or weak while using this product, get to fresh air RIGHT
AWAY. See a doctor. You may have carbon monoxide poisoning.
Risk of Fire Clearances
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
Keep at least 1.5 m (5 ft.) clearance on all sides of
pressure washer including overhead.
6
Figure 9
Connect Hose and Water Supply to Pump
Figure 4
NOTICE Inspect high pressure hose for cuts, leaks or damage.
1. Pull back on collar of high pressure hose (V), slide
onto spray gun (A) and release collar. Tug on hose to
make sure it is secure.
2. Attach other end of hose to outlet (J) on pump and tighten.
3. Inspect inlet screen before connecting garden hose to
water inlet (K). Clean screen if it contains debris or
replace if damaged. DO NOT run pressure washer if
inlet screen is damaged.
4. Make sure water source is capable of supplying water
at a flow rate greater than 14.38 liters (3.8 gallons) per
minute and 0.14-0.55 MPa (1.4-5.5 BAR or 20-80 PSI)
at pressure washer end of garden hose.
5. Run water through garden hose to clean out debris.
NOTICE Use ONLY cold water (less than 38°C (100°F)).
NOTICE Using a backflow preventer at pump inlet could
cause pump damage. There MUST be at least 3 m (10 ft.)
of unrestricted garden hose between pressure washer inlet
and backflow preventer.
WARNING Water that has flowed through a
backflow preventer is considered to be non-
potable.
6. Connect garden hose (not to exceed 15 m (50 ft.)) to
water inlet and tighten.
7. Turn ON water, press red button on gun, and squeeze trigger
to purge system of air. Replace gun if trigger does not lock.
8. Attach nozzle extension (X) to gun (A) and tighten.
9. Pull back on collar of nozzle extension, insert spray
tip (W) and release. Tug on spray tip to make sure it is
securely in place.
Start Pressure Washer
NOTICE DO NOT run pump without water supply
connected and turned on.
1. Move fuel lever (F) to ON (
2. Rotate engine switch (S) to ON (I) position.
3. Move throttle control lever (D) to FAST (
shown on engine as a rabbit.
4. Move choke lever (E) to CHOKE (
NOTICE For a warm engine, be sure choke lever is in
RUN ( ) position.
WARNING! Starter and other rotating parts could
entangle hands, hair, clothing, or accessories resulting
in serious injury. NEVER operate pressure washer
without protective housing or covers. DO NOT wear loose
clothing, jewelry or anything that could be caught in the starter
or other rotating parts. Tie up long hair and remove jewelry.
NOTICE Before starting pressure washer, be sure you
are wearing safety goggles and protective clothing.
WARNING! Spray could splash back or
propel objects resulting in serious injury.
Always wear indirect vented (chemical splash)
safety goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment. Always wear protective clothing
such as a long-sleeved shirt, long pants and close-toed shoes.
Figure 4
) position.
) position,
) position.
BRIGGSandSTRATTON.COM