Safety Instructions For Installation And Maintenance Work; Unauthorised Modification And Manufacture Of Spare Parts; Improper Use; Safety & Control Devices - Wilo -SCP Einbau- Und Betriebsanleitung

• Highly flammable materials are always to be kept
at a safe distance from the product.
• Danger from electrical current must be eliminated.
Local directives or general directives [e.g. IEC, VDE
etc.] and local power supply companies must be
adhered to.
• When the noise generated by the pumpset exceed
80dBA, operators must refer to the local regula-
tion for health protection and limit the exposure
of people to the noise. Please refer to the acoustic
pressure stated on the data plate fitted on the
motor, generally the acoustic pressure generated
by the pumpset is 2dB above this value.
2.6 Safety instructions for installation and
maintenance work
The operator must ensure that all installation and
maintenance work is carried out by authorised and
qualified personnel, who are sufficiently informed
from their own detailed study of the operating
instructions.
Work on the product/unit must only be carried out
when at a standstill. It is mandatory that the pro-
cedure described in the installation and operating
instructions for shutting down the product/unit
be complied with.
Immediately on conclusion of the work, all safety
and protective devices must be put back in posi-
tion and/or recommissioned.
2.7 Unauthorised modification and manufacture of
spare parts
Unauthorised modification and manufacture of
spare parts will impair the safety of the product/
personnel and will make void the manufacturer's
declarations regarding safety.
Modifications to the product are only permissible
after consultation with the manufacturer. Original
spare parts and accessories authorised by the
manufacturer ensure safety. The use of other
parts will absolve us of liability for consequential
events.

2.8 Improper use

The operating safety of the supplied product only
guaranteed for conventional use in accordance
with Section 4 of the operating instructions. The
limit values must on no account fall under or
exceed those specified in the catalogue/data
sheet.
Installation and operating instructions Wilo-SCP
2.9 Safety & control devices
Direct controls are applicable when the pump is
supplied along with motor/panels. When motor/
panel is in end user's scope of supply, it is advised
to go for CE approved motors /panels.
Environmental safety
Disposal of any unwanted/scrap material should
be disposed in appropriate way so as not to cause
any harm to the environment. No hazardous
material is used in Wilo SCP pumps.
NOTE
To avoid ambiguity in the use of the word
„replace" the words „replace" and „renew" are
used in this manual in the following context:
Replace - To put back, in its existing state, a part
or component that has previously been removed.
Renew - To substitute a new part of component
for a worn or damaged one.

3 Transport and interim storage (fig. 1)

Immediately check the pump and transport
packaging for damage in transit upon receipt.
Take the necessary steps within the periods
defined by the transport company in the event of
damage in transit.
DANGER! Risk of getting crushed!
The installation or removal of the product must
not be performed by one person alone.
Measures should be taken to bar persons from
standing beneath a suspended load. Further-
more, it is also prohibited to move suspended
loads over exposed workplaces where people
are present. The fastening devices should be
adapted to the conditions at hand (weather,
hooking system, load, etc.) Use suitable fas-
tening devices to handle the weight of the pro-
duct.
CAUTION! Risk of damage to the pump!
Risk of damage due to improper handling during
transport and storage.
The pump should be protected against humidity,
frost and mechanical damage during transport
and interim storage.

3.1 Handling

CAUTION! Risk of damage to the pump! Risk of
falling!
Pumps should never be lifted with slings enga-
ged below the bearing housing. Eyebolts on
pump top casing are only for lifting top casing
during maintenance. Do not lift complete pump
with the eyebolts. Safe working load of wire
ropes reduces with increase in included angle.
Never put down or pick up the product when it is
not secured. Tilting of the product should be
avoided at all costs.
Only suitable lifting gear and load carrying equip-
ment with valid test certificates and adequate lif-
ting capacity for the loads involved (such as belts/
wire ropes/slings) should be used for lifting &
transporting the product. If chains are used, they
English
47