Regeneration Process For Vehicles With A Diesel Particle Filter (Dpf); Winter Use - Kärcher MC 130 plus Betriebsanleitung

CAUTION
Crush hazard
Never reach into the rod assembly for the emptying mechanism.
1. Stop the vehicle.
2. Apply the parking brake.
3. Bring the travel direction lever into the neutral position (middle
position).
4. Set the switch lever to the "Waste container" position.
5. Switch on the PTO.
6. Lift the right side brush and switch it off by moving the left joy-
stick to the right and then pushing it back.
7. Lift the right side brush by moving the right joystick to the left
and then pushing it back.
8. Switch off the water pump.
9. Wait 20 seconds.
10.Switch off the suction fan.
11.Actuate the toggle switch.
12.Empty the waste container.
Note
Always raise the waste container fully to the end position.
Regeneration process for vehicles with a diesel
particle filter (DPF)
The diesel particle filter retains the fin dust until the fine dust can
be burnt at very high temperatures.
The regeneration process runs either automatically during work-
ing mode or driving mode but can also be started manually if re-
quired.
The higher the speed when driving, or the greater the load, the
less frequent the need for manual regeneration.
Automatic regeneration
In this mode the engine control unit controls the regeneration in-
dependently. A symbol is displayed in the upper symbol bar of the
display when the regeneration process is being performed. The
tool key in the service menu is used for switching between Auto-
matic and Manual regeneration.
Manual regeneration
With Manual regeneration, the driver decides when the Diesel
particle filter (DPF) regenerations process is performed. There
are 5 stages for this.
Manual regeneration - stage 1
Stage 1 is triggered when the DPF has collected the maximum
quantity of fine dust. A corresponding warning is emitted. If the
driver has activated Automatic regeneration then this is started.
A symbol is displayed in the upper symbol bar of the display.
Manual regeneration - stage 2
A flashing symbol is displayed in the upper symbol bar of the dis-
play when Automatic generation has not been performed or the
engine control unit cannot perform this.
Either automatic regeneration or "Parked regeneration" can be
activated.
Manual regeneration - stage 3
A warning symbol in the upper symbol bar of the display notifies
the driver that regeneration should be started immediately. Auto-
matic regeneration is disabled, only "Parked regeneration" is per-
mitted.
The vehicle can only be moved at a limited speed.
Manual regeneration - stage 4
This type of regeneration can only be performed by service per-
sonnel. Automatic regeneration and "Parked regeneration" are
disabled. The vehicle can only be moved forward at a limited
speed.
A warning symbol is visible on the display.
Manual regeneration - stage 5
Regeneration is no longer possible. A corresponding warning
should be displayed in large format. "Parked regeneration" and
automatic regeneration are disabled.
The vehicle can only be moved forward at a limited speed.
"Parked regeneration" can only be performed when the following
requirements are met:
 Travel direction position: Neutral
 Parking brake active
 Engine control unit does not display any error codes
 Accelerator not actuated
Manual regeneration can be activated when these requirements
are met.
The parked regeneration process takes approx. 30 minutes.
The seat cannot be vacated!
WARNING
Risk of burns
During the regeneration process, exhaust gases up to a temper-
ature of 600°C may be omitted.
Do not start the regeneration process in combustible areas.
Note
Only interrupt the regeneration process in the case of an emer-
gency.
Note
If the regeneration indicator on the display lights up during oper-
ation then a regeneration process must be started.
Regeneration can be performed automatically or manually.
Work can continue during Automatic regeneration.
1. For manual cleaning ("Parked regeneration"), stop at suitable
location within 15 minutes.
Regeneration duration is approx. 30 minutes.
2. Set the travel direction to the NEUTRAL position and do not
press the accelerator pedal.
The driver's seat can be vacated during this period.
3. To start the regeneration process, first press function key F 10
(lower right key), then press F 1 for Automatic or F 2 for Man-
ual cleaning.
Note
The engine speed increases noticeably during both types of
cleaning. When cleaning has finished the indicator lamp goes out
and the engine speed decreases again.
Note
The regeneration instructions above should suffice in most cases
and more detailed descriptions are provided in the section "Faults
with display".
1. If frost is expected, check if there is enough antifreeze in the
coolant.
During winter use, the sweeping system and suction mouth must
be disassembled and placed into storage.
English
Parked regeneration
Start regeneration

Winter use

Frost protection
Sweeping system
75