Operation - Scheppach MTP860H Originalbetriebsanleitung

Installing the belt cover (C) (Fig. 24)
• Fix the belt cover (C) with the wing screws (B8) as
shown in fig. 24.
m ATTENTION! The protective housing must be
installed!
Jackleg / Working depth regulator (19)
• Attach the pick-up point for the jackleg (G) with pin
(25a) and split pin (25b) as shown in fig. 25.
• Adjust the desired side position of the jackleg with the
adjusting screws 26A and 26B.
• Insert the jackleg (19) into the opening (26c) at the
pick-up point (G) (Fig.26) and secure it with the fas-
tening pin and the split pin (B6) (Fig. 27).
The depth of the jackleg can be adjusted in vari-
ous positions.
Plow function (Fig. 8/29/32)
Fasten the wheel mountings (I) as shown in fig. 28.
• Grease the tool shaft (3g) and pay attention to the
alignment of the mounting hole (3i) (Fig. 3) when
installing the wheels (K).
1) Insert the fastening pins large (B6) into the openings
and secure them with the split pins.
2) Attach the plow (J) to the desired height using a fas-
tening pin and split pin (B6) as shown in fig. 32.
Adding engine oil
Check the engine oil lever.
Failure to fill engine sump with oil before starting engine
will result in permanent damage and void engine war-
ranty (see Engine operator´s manual ).
Adding transmission oil
Check the transmission oil level.
The gearbox can be permanently damaged and the
gearbox warranty will be extinguished if the gearbox is
not filled with oil before starting (see chapter "Mainte-
nance & cleaning").
Refueling
m WARNING! Always wear protective gloves when
performing maintenance.
This product is powered by a 4 stroke engine.
Store unleaded gasoline in a clean container approved
for gasoline.
Recommended fuel:
This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 91
or higher.
Never use stale or contaminated gasoline or an oil/gas-
oline mixture. Avoid getting dirt or water in the fuel tank.
30 GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
m WARNING! Follow safety instruction for fuel handling.
Always shut off engine before fuelling. Never add fuel to
a machine with a running or hot engine. Move at least 3
m from refuelling site before starting engine. DO NOT
SMOKE!
1. Clean surface around fuel cap to prevent contamina-
tion.
2. Loosen fuel cap slowly.
3. Carefully pour fuel into the tank.
Avoid spillage.
4. Prior to replacing the fuel cap, clean and inspect the
gasket.
5. Immediately replace fuel cap and hand tighten.
Wipe up any fuel spillage.
m WARNING! Check for fuel leaks, if any are found, cor-
rect before use. Contact a Servicing Dealer if necessary.
8. Function
Clutch lever (3)
The forward movement of the blades is carried out by
pulling the lever upwards. The machine is stopped by re-
leasing it.
Throttle trigger (2)
It controls the motor speed. Pulling the throttle lever in the
directions shown makes the engine run faster or slower.
Jackleg / Working depth regulator (19)
It´s for setup of the working depth. The jackleg supports
the operator in the direction and speed regulation of the
ground hook.
By lowering the depth setting the ground hook would be
braked and the working depth would be increased. By lift-
up the depth setting, the speed is faster and the working
depth would be reduced.

9. Operation

9.1 Adding fuel
Fill the fuel tank as instructed in the separate engine
manual.
9.2 Check-up before starting work
Adjusting the clutch (Fig.1)
m CAUTION! THE POWER CULTIVATOR MUST NOT
ROTATE AT IDLE SPEED.
Serious injuries may occur when the cutting tool
rotates at idle speed.
m ATTENTION! Make adjustments on the clutch only by
authorized personnel!
Loosen the lock screw (1b).
To adjust the clutch, turn the adjusting screw screw (1a)
in the appropriate direction:
• Counterclockwise to increase the tension of the clutch
cable,
• Clockwise to reduce the tension of the clutch cable.