Technical Data; Before Starting The Equipment; Attachment And Operation - Scheppach 5904807901 Originalanleitung

6. Technical data

MF1200-4E
Technical data
Cutting data grass trimmer
Cutting circle diameter of line mm
Cutting line diameter mm
Cutting line length m
Maximum speed grass trimmer min
Cutting data brush cutter
Cutting circle diameter of blade mm
Cutter balde thickness mm
Teeth quantity
Maximum speed brush cutter min
Cutting data hedge trimmer
Cutting circle diamter mm
Angle adjustment °
Cutting length mm
Max. cutting speed max. min
-1
Cutting data pole saw
Guide bar legnth mm
Cutting length mm
Guide bar typ
chain pitch
Saw chain type
Chain link thickness "
Oil tank capicity cm
3
Power unit
Motor V / Hz
Engine output W
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 94 dB(A)
pA
Sound power L = 108 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Grass trimmer vibration A = 9,8 m/s
hv
Brush cutter vibration A = 9,8 m/s
hv
Hedge trimmer vibration A = 17,3 m/s
hv
Pole saw vibration A = 13,2 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this
sign: m
28 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
430
2 x 2.0
4
6000
-1
255
1.4
3
7100
-1
24
+90°/0°/-75° (165°)
400
1500
305
254
Oregon 100SDEA318
3/8"
91PJ040X
1.27
125
220-240 V ~ 50 Hz
1200
2
2
2
2

7. Before starting the equipment

Each time before use, check the following:
• That the equipment is in perfect condition and that
the safety devices and cutting devices are com-
plete.
• That all screws are securely fastened.
• That all moving parts move smoothly.

8. Attachment and operation

ASSEMBLY
When assembling this machine, please follow the in-
structions for assembly printed.
Assemble the handle on the machine. Fig. 2-3
1
• Install the front handle as shown on the image 2.
• Make sure that you align the pin with the hole.
Tighten the screws only loosely before you have the
most comfortable working position set to the risers.
The front handle should be aligned as in pictures
2+3 shown, then tighten the screws.
2. Mounting the shaft. Fig. 4
• Open the handle (a)
• Push the shaft into the holder. Make sure that the
metal ball (b) is alignment with the hole (c) and
furthermore locks.
• After this process please fix the shaft by turning
the handle (a).
3. Assemble the safe guard. Fig. 5-7
• Fix the safe guard with hex key and wrench en-
closed as stardard accessories for tighting the nuts
enough. Please see the below pictures showing.
m Warning! Never use the machine without the
guard assembled!
4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 8-9
• Release the nut.
Line up the two holes of flange and shield, use
one screw driver to hold the flange as below and
turn the socket wrench clockwise, the nut will be
released.
• Fit the Nylon cutting head.
Remove another shield after release the nut. Still
hold the flange, take the Nylon cutting head on the
shaft and rotate counter-clockwise, the Nylon cutting
head is fitted. Fig. 19
• Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 10-12
Take the outer flange off after release the nut, then
put the blade (17), outer flange (17b), shield (17a)
and nut according to priority as below picture. Note
the blade rotation direction needs be same as be-
low picture.