Device Description (Fig. 1) - Scheppach MTP860H Originalbetriebsanleitung

1. Introduction
Manufaturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope your new tool brings you much enjoyment and
success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability for
damages to the product or damages caused by the prod-
uct that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advantage
of its application possibilities in accordance with the rec-
ommendations. The operating instructions contain im-
portant information on how to operate the machine safe-
ly, professionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating in-
structions, you have to meet the applicable regulations
that apply for the operation of the machine in your coun-
try.
Keep the operating instructions package with the ma-
chine at all times and store it in a plastic cover to protect
it from dirt and moisture. Read the instruction manual
each time before operating the machine and carefully fol-
low its information. The machine can only be operated by
persons who were instructed concerning the operation of
the machine and who are informed about the associated
dangers. The minimum age requirement must be com-
plied with.
In addition to the safety instructions contained in this
manual and the special regulations of your country, the
technical rules generally accepted for the operation of
identical devices must be observed.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

2. Device description (Fig. 1)

1. Hand grip
2. Throttle trigger
3. Clutch lever
4. Locking clutch lever
5. ON-/ OFF Switch
6. Handlebar
7. Steering column
8. Cover air filter
9. Cover exhaust
10. Fuel filler cap
11. Fuel tank
12. Support wheel
13. Support wheel mounting
14. Blades / Tools
15. Milling broadening
16. Milling protection disc
17. Milling protection housing
18. Start lever
19. Jackleg / Working depth regulator
20. Fuel tap
21. Choke Lever
22. Gear selector lever
23. Height adjustment Handlebar
3. Scope of delivery (Fig. 1+2)
A Housing with motor / gearbox and handlebar (1x)
B Bag with mounting material
B1 Hexagon wrench 10/12 (1x)
B2 Hexagon wrench 12/14 (1x)
B3 Hexagon wrench 13/16 (1x)
B4 Screwdriver (1x)
B5 Rubber ring (6x)
B6 Fastening pin large with split pin (8x)
B7 Fastening pin small with split pin (1x)
B8 Wing screw with washer (2x)
B9 Hexagon screw with edge (1x)
B10 Phillips screw (2x)
B11 Hexagon screw with edge, washer and hexagonal
nut (4x)
B12 Hexagon screw with edge, washer and hexagonal
nut with edge (6x)
C Belt cover (1x)
D Protective cover for handlebar fixation (1x)
E Steering column (7) with gear lever cover (1x)
F Cross connector (1x)
G Mounting point Jackleg / Working depth regulator
(1x)
H Front Hand grip (1x)
I Wheel mount (2x)
J Plow (1x)
K Wheel (2x)
L Motor manual
M Original instruction manual
2 Throttle trigger (1x)
12 Support wheel (1x)
14 Blades / Tools (2x)
15 Milling broadening (2x)
GB 25