Technical Data; Before Commissioning; Operation - Scheppach Therbio Originalbetriebsanleitung

Check the cable for damage.
• Remove the plug from the socket before all work
on the machine, before rest periods and when the
machine is not being used.
• Mains cables may not have a smaller cross section
than 2 x1.5 mm².
• Charge the batteries only in chargers that have
been recommended by the manufacturer. There is
a risk of fire if a charger for a particular type of bat-
tery is used for another type of battery.
• Use only the designated type of battery in the pow-
er tool. Use of other batteries can cause injury and
fire.
• While the battery is not being used, keep it away
from paperclips, coins, keys, nails, screws and oth-
er small metal objects which could bridge the con-
tacts. A short-circuit between the battery contacts
can cause burns or fire.
• If used incorrectly, liquid may leak from the battery.
Avoid contact with it. In the event of accidental con-
tact, rinse with water. If the liquid gets in your eyes,
also consult your doctor. Leaking battery liquid can
cause skin irritation and burns.
• WARNING! RISK OF EXPLOSION! Never try to
charge non-rechargeable batteries.
• Warning! This electric tool generates an elec-
tromagnetic field during operation. This field can
impair active or passive medical implants under
certain conditions. In order to prevent the risk of
serious or deadly injuries, we recommend that per-
sons with medical implants consult with their physi-
cian and the manufacturer of the medical implant
prior to operating the electric tool.

Technical Data

Rated voltage
Heating operation rated output
Heating time (full tank)
Shut-off temperature
Pump delivery rate
Rated battery voltage
Battery capacity
Battery type
Tank contents
Weight
efore commissioning
B
The position of the machine must be stable.
•
Before commissioning, all safety devices must be
•
installed correctly.
Before connecting the machine, ensure that the
•
data on the rating plate complies with the mains
data.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
•
Setup
Warning! Disconnect the plug before all maintenance,
retooling and assembly work on the weed killer.
Place all supplied parts on a flat surface. Group the
same parts.
Handle assembly (Fig. 2)
1. Loosely screw the compression fittings (5) on the
2. Firmly attach the handle (6).
3. Tighten the compression fitting (5).
Assembly of lance with hose (Fig. 3)
1. Screw the lance (9) together with the hose (25).

Operation

Filling with water (Fig. 4)
1. Remove sealing cap (4) as shown in Fig. 4.
2. Fill a maximum of 20L of water using a suitable
3. Wipe up spilled water with a dry towel immediately.
4. Fit the sealing cap and tighten as shown in Fig. 4.
Mains connection (Fig. 5)
1. Open the sealing cap of the spray-water-protected
2. Connect the mains plug (3) with extension cable
220-240V~
Heating mode (Fig. 6/8)
3000W
1. Switching on: Press the ON/OFF button (14) once
approx.
45min
99°C
0.5 L/min
11.1V
2. If there are leaks in the water system, switch off the
2000mAH
Lithium-Ion
20L
7.6 kg
3. Heating the water: Press the heating button (21)
4. When the maximum temperature is reached, three
Only ever plug the machine into an appropriately
installed shockproof socket which is fused with at
least 16 A.
designated threads.
container or funnel. Use pure rainwater or distilled
water, if applicable, because it will not cause calcifi-
cation.
mains plug (3).
(11) to the mains.
- A beep sound is issued. The operation LED (15)
begins to illuminate. The water temperature is dis-
played on the temperature indicator (17). If there
is too little water in the system, the water shortage
warning LED (16) illuminates.
device immediately with the ON/OFF button (14)
and disconnect the device from the mains with the
mains connection cable. There is a risk of electric
shock!
and the water in the tank is heated up. The current
water temperature can be seen on the temperature
indicator (17). Depending on the filling temperature
of the water, it can take up to 45 minutes before the
water has been heated up to maximum tempera-
ture.
short beeps are issued and the LED for heating
mode (22) goes out.
GB І 19