Installation Instructions - Simons Voss Technologies KU SmartHandle Kurzanleitung

smartHandle only acts on the mortise lock latch bolt.
•
the simonsvoss smartHandle may only be used for its intended purpose: opening and locking doors. no
•
other use is permitted.
when used in combination with panic locks, you must ensure that all parts of the locking system are fully
•
functional and the mortise lock panic function is guaranteed to work after installation.
modifications or further technical developments cannot be excluded.
•
this documentation has been compiled in accordance with the best knowledge available to us. However,
•
errors cannot be ruled out. no liability is accepted in such cases.
should there be differences in the content of other language versions of this documentation, the german
•
version applies in cases of doubt.

installation instructions.

batteries are already installed when the cylinder is delivered!
•
when installing the digital smartHandle 3062 (active and Hybrid), ensure that there are no sources of low-
•
frequency interference in the surrounding area.
smartHandles (active and Hybrid) should be installed at least 0.5 m from one another while smartrelays
•
active or activation units should be 1.5 m from one another.
smartHandle must be fitted, so that it is flush with the door. You must install the product as specified to
•
ensure that it is structurally stable and will have a long service life.
You must not strike parts of the smartHandle during installation.
•
the two inlays in the cover are locked into position with a clip mechanism. these may only be removed
•
using the simonsvoss installation tool.
programme smartHandle before installing! the smartHandles cannot be actuated with a transponder
•
(active/Hybrid) or a smartcard/smarttag before they are programmed for the first time!
smartHandles may be difficult to fit in mortise locks with a retaining nut. You must not alter the retaining
•
nut in any way, using a file, for example; otherwise, the handle's guide piece will no longer fit accurately.
ensure you do not damage the edges or deform its shape in any way. once fitted, the handle must not be
•
loose when in its horizontal position.
as it is no longer possible in the case of most handles to push the inlays over the handles after installation
•
due to the design, it is recommended to push them over the handle first before it is installed.
installation of smart HanDle – mo.
1. optional: handles, escutcheons, fittings and other door furniture fitted to the door are to be removed.
2. the smartHandle is partly assembled when delivered. for information on disassembly, please consult the
„disassembly" section and follow steps 9,11 and 12.
3. on some handles it is not possible to apply the inlay once the handle is installed (e.g., offset handles). for
these handles, push the inlay (with the logo facing outward) over the outer handle. generally speaking it is
possible to proceed for all handles like this.
4. optional: in a lock with a 8.5 mm or 10 mm spindle, push the the corresponding sleeve (8 mm --> 8.5
mm or 8 mm --> 10 mm) through the retainer opening in the mortise lock.
5. push the inside fitting spindle through the retainer slot in the door's mortise lock, so that the fitting is flush
with the door. ensure you do not squash the 3-pole cable when doing so.
6. position the inside fitting in such a way that it is parallel to the door.
mark the drill holes required through the corresponding holes in the inside fitting.
7.
8. remove inside fitting from the door.
9. drill the holes with a diameter of 8 mm (top hole) and 13 mm (lower hole) through the door.
10. insert outer handle horizontally into the outer fitting, placing it in the direction that you require, depending
on whether it is a din left-hand or right-hand door.
11. place handle fastener piece into position (see diagrams 2 and 3)
12. Hold the outside handle and use the spanner to rotate the fastener piece about 75° to the right until it fits
into position (diagrams 4 and 5). if you do not fit it correctly, the handle may come loose again.
13. the inside fitting is mounted onto the inner surface of the door. push the inner fitting spindle through the
mortise lock retainer slot and push the inner fitting onto the door until it is about 5 cm away.
14. push the 3-pole cable for the inside fitting through the lower hole (13 mm in diameter) and ensure that it
doesn't get caught or buckled.
11