3M PELTOR WS LiteCom Pro III Headset Bedienungsanleitung Seite 16

10. PRODUCT LIFETIME
It is recommended that you replace your product within
5 years from date of manufacture. The lifetime of the product
will be highly dependent on the environment in which the
product is stored, used, serviced, and maintained. The user
must regularly inspect the product to determine when it has
reached its end of life. Examples that the product may have
reached its end of life are:
• Visible defects such as cracks, deformations, loose or
missing parts.
• Experience of a deterioration in the hearing protector's
attenuation performance, strange noise or abnormal high
sound volumes from the product's electronic sound
reproduction.
NOTE: Product lifetime does not include batteries.
11. CLEANING AND MAINTENANCE
Carry out a visual battery condition check. Replace if battery
leakage or defects are detected.
Use a cloth wetted with soap and warm water to clean the
outer shells, headband and ear cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn the
earmuffs outwards, remove the ear cushions and foam liners,
and allow to dry before reassembly. The ear cushions and
foam liners may deteriorate with use and should be examined
at regular intervals for cracking or other damage. When used
regularly, 3M recommends replacing the foam liners and ear
cushions at least twice a year to maintain consistent
attenuation, hygiene, and comfort. If an ear cushion is
damaged, it should be replaced.
See SPARE PARTS AND ACCESSORIES.
11.1. REMOVING AND REPLACING THE EAR
CUSHIONS
(Figure M:1 - M:3)
M:1 To remove the ear cushion, slide your fingers under the
inside edge of the ear cushion and firmly pull straight out.
M:2 Remove existing liner(s) and insert new foam liner(s).
M:3 Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until ear
cushion snaps in place.
11.2. REPLACING THE CARRIER ATTACHMENT
PLATE
(Figure K:1 - K:2)
For proper fitting on different compatible carrier devices, the
carrier attachment plate may need to be replaced. Find the
recommended attachment in table E. The headset comes
assembled with P3E carrier attachment. Other plates can be
obtained from your dealer. A screwdriver is needed to replace
the carrier attachment plate.
K:1 Loosen the screw holding the plate and remove the plate.
K:2 Attach the appropriate plate while ensuring the left (L)
and right (R) designated plates are on the appropriate
earmuff, if applicable, and then tighten the screw.
11.3. APPLYING MICROPHONE PROTECTOR
TAPE
(Figure N:1 - N:5)
To protect the boom speech microphone from humidity and
dirt, use microphone protector HYM1000.
Attaching the protector:
N:1 Use a pair of scissors to cut 100 mm of HYM1000 Mic
protector tape. Remove the protective paper.
N:2 Place the microphone in the end of the tape as shown in
the picture.
N:3 Fold the protecor tape and make sure that the
microphone is covered.
N:4 Press tighly to seal the protector tape.
N:5 The microphone is now ready to use.
12. SPARE PARTS AND ACCESSORIES
NOTE: The accessories listed below are for Non-Intrinsically
Safe products. For approved spare parts and accessories for
Intrinsic Safety products, refer to separate Safety Guide
included in the packaging of the product.
Article number
ACK081 Rechargeable battery pack, 3.7 V.
Only for use with the non intrinsically
safe WS™ LiteCom Pro III Headset.
ACK082 Rechargeable battery pack, 3.7 V.
AL2AI/SP Battery charging USB cable for
ACK081.
AL2AH Battery charging USB cable for
ACK082.
FR08 Power supply with USB connector.
FL5602-50 External PTT for WS™ LiteCom Pro
III Headset, EX/IS.
FL6BR Connecting cable with J11 connector
(type Nexus TP-120) for use with a
PELTOR
2-way radio.
HY100A Clean – single-use protectors.
Single-use protector for the ear
cushions. Package of 100 pairs.
HY83 Replaceable hygiene kit consisting of
two sets of foam liners and two
snap-in ear cushions.
HYM1000 Mic protector.
Moisture and wind-resistant tape.
Protects the speech microphone.
Package of 4.5 meters for about
50 replacements.
M171/2 Windshield for MT73 speech
microphones. Two per package.
M60/2 Windshield for ambient microphones.
One pair per package.
EN
Description
adapter and an external
TM
7