3M PELTOR WS LiteCom Pro III Headset Bedienungsanleitung Seite 15

EN
The headset can be paired to two Bluetooth devices, and can
be connected to two devices at the same time.
To pair a second device using Bluetooth pairing, make a short
press on the On/Off/Mode button to enter the menu. Use the
On/Off/Mode button to navigate through the menu, a voice
will confirm the setting, "Bluetooth pairing". Press the [+]
button to set the headset in pairing mode. Press the [–] button
to exit pairing mode.
Make sure that Bluetooth is activated on your Bluetooth
device. Scan for devices and select "WS LiteCom Pro III
Headset". A voice message will confirm when the pairing is
complete, "Pairing complete".
NOTE: By default, the radio VOX functionality is disabled
when taking a phone call via a Bluetooth connection. Once
the call has ended, VOX is automatically back on. To transmit
on the two-way radio during a phone call, press the PTT
button. If the PTT button is pressed during a phone call, your
voice will only transmit through the two-way radio and not to
the phone call. To activate VOX during a phone call, double
press the PTT button. Your voice will then be transmitted to
both the two-way radio and the phone call.
8.10.3. OPERATING YOUR BLUETOOTH DEVICE VIA
THE HEADSET
NOTE: The latest paired Bluetooth device is the one you
operate via the headset.
Bluetooth Scenario
A Bluetooth device is
connected but no activity
A Bluetooth device is
connected and receiving
an incoming call
Bluetooth device is
connected, and has an
ongoing call
You can also stream music from your Bluetooth device. The
table below shows commands when a device is connected
and streaming is in progress.
Action
Short press
Double short press
Triple short press
Long press
6
Action Feature
Long press Voice dial
Short press Answer call
Long press Reject call
Short press Hang up
Feature
Play/pause
Next track
Previous track
Voice dial
9. MENU FUNCTIONS
9.1. MENU
To enter the menu, make a short press on the On/Off/Mode
button. Use the On/Off/Mode button to navigate through the
menu and the [+] and [–] buttons to adjust the settings.
After 10 seconds of inactivity, the headset will exit the menu
(you can also leave the menu by pressing both the [+] and [–]
button at the same time).
These are the options available in the menu.
Menu option
Channel Lists all the programmed channels in
the headset, up to 70.
Radio volume Adjusts the volume level of the
incoming radio sound. (OFF, 1–5)
Ambient listening Ambient listening sound helps protect
volume your hearing from potentially harmful
noise levels. Constant rumbling and
other potentially harmful noises are
reduced, and you can still speak
normally and make yourself heard.
(OFF, 1–5)
Bluetooth radio Adjusts the volume level of a Bluetooth
volume connected communication radio, 1–5.
Bluetooth pairing Press [+] button to set the headset in
pairing mode. Press [–] button to exit
pairing mode.
Battery status Battery status is measured and the
result is played to the user. Press [+]
button to repeat the information.
Language Adjusts the ghost voice language
between all installed languages.
Sub channel/ Sets the subchannel of an analog
Color code channel according to table (G) and (H) if
(if activated) it is enabled, 0–121. Sets the color code
of a digital channel, 0–15.
Output power This feature controls the power level of
(if activated) the radio transmitter. There are three
output power levels: low, medium, and
high. The low setting will reduce the
communication range but increase the
battery life.
Reset Press [+] button for 2 seconds to reset
the headset to its default state.
When browsing long lists such as channel and sub channel,
press and hold either the [+] or [–] button to skip ten items at the
time.
The headset will automatically exit the menu after 10 seconds.
Or, simultaneously press and hold the [+] and [–] buttons for
2 seconds. A beep will confirm the menu has been exited.
Description