3M PELTOR WS LiteCom Pro III Headset Bedienungsanleitung Seite 13

EN
Table ref.
C:14 Sound output level for maximum input signal
(dB(A))
C:15
Time equivalent to 82 dB(A) over 8h (hh:mm)
for maximum input signal
4.3. CARRIER DEVICES
These earmuffs should be fitted to and used only with the
carrier devices listed in Table E. These earmuffs were tested
in combination with the carrier devices listed in Table E, and
may give different levels of protection if fitted to different
carrier devices.
Explanation of the carrier attachment table:
Table ref.
E
Compatible carrier devices
E:1 Manufacturer
E:2
Model
E:3 Attachment code
E:4
Head size: S = small, M = medium, L = large
5. OVERVIEW
5.1. P) COMPONENTS
(Figure P)
5.1.1. HEADBAND MT73H7A4D10*
* Designates a product variant
P:1 Headband (PVC, PA)
P:2 Headband wire (stainless steel)
P:3 Two-point fastener (POM)
P:4 Cushion (PVC foil and PUR foam)
P:5 Foam liner (PUR foam)
P:6 Cup (ABS)
P:7 Environmental microphone (PUR foam)
P:8 Speech microphone MT73 (ABS)
P:9 Antenna (PE, ABS, TPE)
P:10 Auxiliary port (brass)
P:11 Li-ion battery (PC, ABS)
P:13 On/Off/Mode button (silicone)
P:14 + button (silicone)
P:15 – button (silicone)
P:16 PTT button for built-in two-way radio (PBT)
P:17 Bluetooth button (PBT)
5.1.2. FOLDING HEADBAND MT73H7F4D10EU-50,
MT73H7F4D10NA-50
P:18 Headband (TPE)
P:19 Headband wire (stainless steel)
5.1.3. CARRIER ATTACHMENT MT73H7P3E4D10EU
P:20 Cup supporting arm (stainless steel)
5.1.4. NECKBAND MT73H7B4D10EU
P:21 Neckband wire (stainless steel)
P:22 Neckband cover (PO)
4
Description
Description
6. SETUP
6.1. GENERAL
The following points covers the main actions to make the
product ready for operation.
6.2. CHARGE BATTERY/BATTERIES
Make sure you have read and understood the contents of
Chapter 2 "SAFETY", before charging the battery/batteries.
The battery can be charged in a powered off headset, or
separated from the headset. The ACK081 battery is equipped
with an LED that indicates with a green light when the charging is
complete. Red light indicates charging.
Insert the rechargeable battery in the battery compartment.
Push down the latch.
Charging time for ACK081 is approx. 3 h.
Charging time for ACK082 is approx. 12 h.
Low battery warning
When the battery voltage level is low, the headset will warn you
with a voice message. This message is repeated until you charge
the battery or the battery voltage reaches a critical level and the
headset powers off.
6.2.1. CONNECT AN EXTERNAL RADIO
(Figure P)
Connect your external communication radio via the auxiliary
port (P:10) (cable not included).
7. FITTING INSTRUCTIONS
Inspect the hearing protector before each use. If damaged,
select an undamaged hearing protector or avoid the noisy
environment.
7.1. HEADBAND
(Figure J:1 - J:3)
J:1 Slide out the cups and tilt the top of the shell out, as the
cable must be on the outside of the headband.
J:2 Adjust the height of the cups by sliding them up or down
while holding the headband in place.
J:3 The headband should be positioned across the top of
the head as shown and should support the weight of the
headset.
7.2. NECKBAND
(Figure J:9 - J:11)
J:9 Place the cups in position over the ears.
J:10 Keep the cups in position, place the head strap on top of
your head and lock it tight in position.
J:11 The head strap should be positioned across the top of
your head and should support the weight of the headset.