Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Approval
distribution board in the vehicle� Secure the device
against being switched on again�
Motorhomes and caravans may have self-sufficient 230
V AC power supplies (e�g� inverters, generators, solar
panels)�
Take the self-sufficient power supply into account�
Motorhomes and caravans may have an external socket
for the mains supply�
When carrying out electrical work in the vehicle,
ensure that nobody else can accidentally plug a live
connector cable into the external socket�
Prevent the connection of an external power supply,
e�g� insert a dummy plug with the warning "Cau-
tion! Electrical work in the vehicle" into the external
socket�
2.3.2 Battery voltage 12 V DC
Parts of the device are powered by 12 V batteries via
the vehicle's on-board power supply� In the event of
high electrical loads or a short circuit, very high cur-
rents can flow through the supply lines, potentially
causing the cables to heat up, a cable fire to break out
and strong sparks and arcs to be produced�
Use sufficient cable cross-sections�
Fuse cables with appropriate safety fuses�
Cover the battery poles�
Cover open electrical contacts�
Use isolated plug-in connectors�
2.4
Device safety
2.4.1 Instructions affixed to the device
Observe the instructions affixed directly to the de-
vice�
Instructions affixed to the device must always be
legible�
2.4.2 Protective devices attached to the device
Risk of injury if safety devices are missing or faulty�
After installation, attach all safety devices (covers,
safety instructions, earth cable, etc�)�
Exchange or replace faulty safety devices that have
become unusable�
2.4.3 Genuine spare parts
Avoid property damage due to incorrect additional
components, spare and wear parts� Non-approved
components, spare and wear parts that have not been
tested with the system may damage the device and the
vehicle� The installation of non-approved components,
spare and wear parts as well as non-approved modifica-
tions and conversions are deemed to be improper and
may limit the function, safety and warranty�
Only use genuine components, spare and wear parts
from Truma Gerätetechnik GmbH & Co KG�
Do not use parts that are damaged�
Use screws with sealant only once�
20
EN
3
Approval
An acceptance test by a vehicle expert is not usually
necessary if the device is installed correctly in accord-
ance with the installation instructions and the ABE
(general vehicle type approval)�
Exceptions: Acceptance by a vehicle expert is required
for installation of a low chassis kit and whenever the
chassis geometry deviates from the descriptions in the
installation instructions�
The manoeuvring system complies with other require-
ments of EC Directives and Standards (see Declaration
of Conformity)�
Any modifications made to the device, opening the
housing or the use of any spare parts or functionally
significant accessories other than Truma original parts,
or failure to comply with the contents of the operating
and installation instructions invalidates the warranty
and precludes any liability claims� This will also invali-
date the operating permit for the device�
4
Scope of delivery and tools
required
For an overview of the scope of delivery, see Chapter
6�1�1�
The following tools and equipment are recommended
for installation of the manoeuvring system:
AF 10 mm,13 mm and 17 mm socket wrenches,
•
ring spanners or open-jawed spanners
Allen key 4 mm
•
Torque wrenches (2�5 – 40 Nm)
•
Cable cutter / crimping tool
•
Electric drill / screwdriver / keyhole saw, diameter 25
•
mm
Trolley jack with suitable support trestles, lifting plat-
•
form (2 t) or a pit
Adequate lighting
•
5
Preparing for installation
5.1
Technical requirements
Note� The load capacity of the caravan is reduced by
the weight of the manoeuvring system�
Note: The permissible gross weight of the caravan
for use with a manoeuvring system must not be
exceeded�
No technical modifications may be made to the
device or to the attachments on the chassis, other-
wise the warranty or guarantee of the manoeuvring
system will be rendered null and void�
5.2
Important installation dimensions
A distinction is made between L-profile and U-profile
frames:
L-profile
Mover smart M RS1
60040-00463 ∙ 00 ∙ 09/2023
Werbung
