Werbung
Verfügbare Sprachen
Verfügbare Sprachen
10.3 Adjusting the drum (fig. 1, fig. 12a/12b)
The concrete mixer must be engaged in a certain mixing posi-
tion for concrete and mortar production. Only the correct mix-
ing position ensures the best mixing ratio and guarantees a
trouble-free working process.
1. Always hold the pivoting handle (1) firmly to adjust the
drum (6).
2. Release the swivelling device by pulling the pivoting han-
dle (1) towards you. The latch is released from the grating
disc (14).
3. Swivel the mixing drum (6) to the recess corresponding to
your mix. The mixing positions are marked on the grating
disc (14) by recesses:
• Fig. 12a: Drum position for the production of mortar
• Fig. 12b: Drum position for the production of concrete
4. When the drum (6) is in the desired position, engage the
pivoting handle (1) into the grating disc (14) again.
10.4 Filling (fig. 12a + 12b)
m ATTENTION!
Health risk and danger of injury!
Breathing in dust can cause damage to health. Do not touch
the cement or admixtures without protective gloves.
-
Wear a breathing mask.
-
Wear protective gloves and never reach into the mixing
drum while it is running.
m WARNING!
Tipping hazard!
Pay attention to the stability of the concrete mixer before filling.
-
Only operate the concrete mixer on a firm, level (non-tilt-
ing) surface.
-
Do not change the location of the concrete mixer when
filling or when the drum is running.
1. Press the ON/OFF switch (5) "I" (green button) to start
the device.
2. Check the mixing position on the grating disc (14):
• Fig. 12a: Drum position for the production of mortar
• Fig. 12b: Drum position for the production of concrete
3. Fill the mix while the drum is running (6). Do not overfill the
drum (6). Caution! Danger from moving parts!
4. Do not throw material into the mixing drum with great mo-
mentum in order to prevent it sticking to the underside of the
drum. Feed in the material in small portions.
5. Before filling, make sure that the opening of the drum (6) is
aligned so that no mix can fall out of the drum (6).
Note: Ask a specialist for advice about the composition and
quality of the mix.
10.5 Emptying (fig. 13a)
1. Unlock the swivelling device by pulling the pivoting handle
(1) towards you. The latch is released from the grating disc
(14).
2. Now swivel the drum (6) downwards slowly to empty it.
3. Place a sufficient container (e.g. a mortar bucket) beneath
the drum (6). Make sure that no mix can get onto the floor.
8
GB/IE
11. Electrical connection
The electrical motor installed is connected and ready for op-
eration. The connection complies with the applicable VDE and
DIN provisions.
The customer's mains connection as well as the extension cable
used must also comply with these regulations.
11.1 Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the connection cables are disconnected from elec-
trical power when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables marked
with H07RN.
The printing of the type designation on the connection cable
is mandatory.
For single-phase AC motors, we recommend a fuse rating of C
16A or K 16A for machines with a high starting current (from
3000 watts)!
12. Cleaning
m WARNING!
Risk of injury!
The product can start unexpectedly and cause injuries.
-
Switch off the motor before carrying out any cleaning or
maintenance work.
-
Disconnect the mains plug before carrying out any clean-
ing work.
NOTE!
Risk of damage!
Damage to the motor can occur if water penetrates into the
motor unit. Do not tap on the mixing drum with hard objects
(hammer, shovel, etc.). A dented mixing drum impairs the mix-
ing process and can be more difficult to clean.
-
Clean the product with a brush or a scraper.
-
Do not immerse the product in water or other liquids and
do not spray the motor unit with a high-pressure cleaner.
We recommend that you thoroughly clean the inside and out-
side of the device directly after every use. Never remove dirt
with a hammer, shovel or the like.
Werbung
