Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2. The mixing plant (12) is only tightened once the drum up-
per section (13) has been installed (see section 9.5).
Note: In order to make correct installation of the mixing plant
easier, two arrows are attached to the upper and lower drum.
If you are not sure whether the mixing plant has been installed
correctly, you can test this. To do this, place the upper drum
on the lower drum and turn them until the two arrows point
towards each other.
9.5 Installing the drum upper section (13)
(enclosed accessories bag E) (fig. 8)
1. Put the drum upper section (13) onto the lower drum (10).
Make sure that the fixing holes of the upper and lower
drum align with each other.
Attention! The glued-on arrows mark the exact align-
ment of the drum lower section (10) and drum upper sec-
tion (13).
2. Fix the drum upper section (13) by attaching the M6x16
screws, washers and M6 nuts (E2).
3. Then tighten the screws (E2) crosswise using a Phillips
screwdriver and an open-ended spanner size 10 (not in-
cluded in the scope of delivery).
4. Fasten the top end of the mixing plant (12) by attaching an
M8x20 fillister head screw, a rubber washer and an M8
nut (E1). The rubber washer (E1) must be between the mix-
ing plant (12) and the drum upper section (13).
5. Then tighten the screws (D1) and (E1) using a Phillips
screwdriver and an open-ended spanner size 13 (not in-
cluded in the scope of delivery).
9.6 Installing the grating disc (14)
(enclosed accessories bag F) (fig. 9)
1. Install the grating disc (14) by attaching the M8x25 hex-
agonal bolts, washers and hexagonal nuts (F1) to the ma-
chine stand (2).
2. Then tighten all screws using one or two open-ended span-
ners (size 13) (not included in the scope of delivery).
9.7 Installing the pivoting handle (1)
(enclosed accessories bag G) (fig. 10)
1. Guide the spring (G2) into the rod tube of the pivoting
handle (1) from below.
2. Hold the spring (G2) in place with a finger.
3. Place the pivoting handle (1) above the shaft of the drum
lower section (10) so that the spring lies on the shaft.
4. Push the pivoting handle (1) down until the holes in the
shaft of the drum lower section (10) align with the holes in
the pivoting handle (1).
5. Fasten the pivoting handle (1) using the M8x55 hexago-
nal bolt, a washer and a nut (G1).
6. Then tighten the screw (G1) using two open-ended span-
ners size 13 (not included in the scope of delivery) until the
pivoting handle (1) can still be turned easily.
Note: The pivoting handle must rest on the shaft so it can ro-
tate and it does not slip off. It must be able to grip easily into
the holes of the grating disc (14).
9.8 Installing the motor unit (4)
(enclosed accessories bag H) (fig. 11)
1. Place the O-ring (H3) into the circular nut in the central
hole of the bearing holder (11) on the frame middle sec-
tion (8).
2. Push the motor unit (4) onto the shaft (2a) of the frame
middle section (8). Pay attention to the position of the shaft
(2a) and threaded bolts (4a) on the frame middle section
(8) or the motor unit (4).
3. Then fasten the motor unit (4) by attaching a M8x60 hex-
agonal bolt, a washer and an M8 nut (H1).
4. In addition, turn the two M8 nuts (H2) on the threaded
bolts (4a) of the motor unit (4).
5. Then tighten all screws using one or two open-ended span-
ners (size 13) (not included in the scope of delivery).
10. Start up
m Attention!
Always make sure the device is fully assembled before com-
missioning!
Only operate the concrete mixer if no parts are missing or
faulty and if the connection cable is not damaged.
10.1 Setup
1. Set up the concrete mixer horizontally on a level, non-tilting
and firm surface. Prevent the machine from sinking into the
ground.
2. Do not set up the concrete mixer on the connection cable!
3. Lay the connection cable so that it cannot be kinked,
crushed or damaged in any other way.
Note:
The drum (6) must be able to swivel to the right and left. Make
sure that a sufficient container (e.g. a mortar bucket) is beneath
the drum (6) for emptying the drum (6). When setting up the
machine, make sure that the mixing drum can be emptied freely.
10.2 Switching on/off (fig. 1)
m ATTENTION!
Risk of injury!
A rotating mixing drum can lead to injuries.
-
Do not reach into the mixing drum while it is running.
Do not put any objects into the mixing drum while it is run-
-
ning (e.g. shovel or similar).
1. Plug the device into the socket.
2. Press the ON/OFF switch (5) "I" (green button) to start
the device.
3. Press the ON/OFF switch (5) "0" (red button) to switch
off the device.
10.2.1. Thermal protection
With overloading or overheating, the protective shut-down inte-
grated in the device switches off for safety reasons.
1. Wait approx. 15 minutes until the motor has cooled down.
2. Restart the device by pressing the ON/OFF switch (5) "I"
(green button).
GB/IE
7
Werbung
