Werbung
Verfügbare Sprachen
Verfügbare Sprachen
7. Technical data
Motor ................................................................ 230 V∼ / 50 Hz
Motor power ...............................................................220 Watts
Max. speed ................................................................ 2850 min
Max. speed, drum .........................................................27.5 rpm
Capacity .................................................................................62 l
Protection category ...............................................................IP44
Operating mode* ...........................................................S6 30%
Protection class ............................................................................II
Dimensions .............................................1161 x 550 x 935 mm
Weight .................................................................................26 kg
Technical changes reserved!
*S6 30 %: Continuous duty with intermittent loading (operat-
ing time 10 min.)
In order avoid impermissible overheating of the motor, the mo-
tor should be driven for only 30% of the operating time with the
stipulated nominal power and must then continue to run with no
load for the remaining 70% of the operating time.
Noise and vibration
m Warning:
Noise can have serious effects on your health. If the machine
noise exceeds 85 dB (A), please wear suitable hearing protec-
tion.
Noise data
The noise values have been determined in accordance with
EN 62841.
Sound pressure level L
..........................................61.14 dB(A)
pA
Uncertainty K
................................................................2.54 dB
pA
Sound power level L
............................................82.12 dB(A)
WA
Uncertainty K
...............................................................2.54 dB
WA
Guaranteed sound power level L
WA
8. Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, keep the packaging until the expiry of the war-
ranty period.
m DANGER
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
6
GB/IE
-1
.............................85 dB(A)
9. Assembly / Before commissioning
m Attention!
Always make sure the device is fully assembled before com-
missioning!
In order to make assembly easier, assembly must be carried out
by two persons. The enclosed accessories bag (15) includes
all the small parts (A to H) required for assembly (see fig. 3).
9.1 Installing the foot (7) on the frame middle sec-
tion (8) (enclosed accessories bag A) (fig. 4)
1. Hold the foot (7) to the frame middle section (8). Then
attach the M8x60 hexagonal bolt with two washers and
an M8 nut (A2). Make sure that the position of the holes
and the foot (7) on the frame middle section (8) is correct.
2. Then screw in the M8x40 hexagonal bolt with a washer
(A1) into the front of the foot (7).
3. Tighten all screws using one or two open-ended spanners
(size 13) (not included in the scope of delivery).
9.2 Installing the foot with wheel axle (9) and
transport wheels (3) on the frame middle sec-
tion (8) (enclosed accessories bag B) (fig. 5)
1. First, install the transport wheels (3) by sliding them onto
the wheel axles (9). Then insert the split pins (B3) into the
hole and bend them apart in order to secure the transport
wheels (3).
2. Now push the wheel caps (B4) onto the transport wheels
(3).
3. Then hold the foot with wheel axle (9) to the frame middle
section (8). And attach the M8x60 hexagonal bolt with
two washers and an M8 nut (B2). Pay attention to the posi-
tion of the holes.
4. Now screw in the M8x40 hexagonal bolt with a washer
(B1) into the front of the foot with wheel axle (9).
5. Then tighten all screws using one or two open-ended span-
ners (size 13) (not included in the scope of delivery).
9.3 Installing the drum lower section (10) (enclosed
accessories bag C) (fig. 6)
1. Fit the bearing support (11) onto the drum lower section
(10) at the intended location.
2. At the same time, insert the bearing of the drum lower sec-
tion (10) with the premounted bearing support (11) into
the opening of the machine stand (2). Make sure that the
bearing support (11) is above the foot with wheel axle (9).
3. Pay attention to the position of the holes. Attach the M8x55
screws with two washers and M8 nuts (C1) each onto both
sides of the machine stand (2).
4. Then tighten all screws using one or two open-ended span-
ners (size 13) (not included in the scope of delivery).
9.4 Installing the mixing plant (12) (enclosed acces-
sories bag D) (fig. 7)
1. Fit the mixing plant (12) onto the drum lower section (10)
by attaching an M8x20 fillister head screw, a rubber
washer and an M8 nut (D1). Make sure that the holes/
surfaces at the top end of the mixing plant (12) are facing
outwards. The rubber washer (D1) must be between the
mixing plant (12) and the drum lower section (10).
Werbung
