Maintenance - Makita DLS714 Betriebsanleitung

3. Remove the workpiece material between the
grooves with a chisel.
Carrying tool
АůRІIІżŚ StШЩЩОrăЩТЧăТsăШЧХвăПШrăМКrrвТЧРă
КЧНăstШrКРОăЩurЩШsОsăКЧНăsСШuХНăЧОЯОrăЛОăusОНă
ПШrăКЧвăМuttТЧРăШЩОrКtТШЧs. The use of the stopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
sОrТШusăЩОrsШЧКlăТЧУurв.
CAUTION: ůХаКвsăsОМurОăКХХăЦШЯТЧРăЩШrtТШЧsă
ЛОПШrОăМКrrвТЧРătСОătШШХ. If portions of the tool move
or slide while being carried loss of control or balance
ЦКвăШММurărОsultТЧРăТЧăЩОrsШЧКlăТЧУurв.
►Fig.52
1. Remove the battery cartridge.
2. Secure the blade at 0° bevel angle and the turn
base at the full right miter angle position.
3. Secure the slide poles so that the lower slide pole
is locked in the position of the carriage fully pulled to
operator and the upper poles are locked in the position
of the carriage fully pushed forward to the guide fence.
4. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
5. Carry the tool by holding both sides of the tool
base. If you remove the holders, dust bag, etc., you can
carry the tool more easily.

MAINTENANCE

АůRІIІżŚ ůХаКвsăЛОăsurОătСКtătСОăЛХКНОăТsă
sСКrЩăКЧНăМХОКЧăПШrătСОăЛОstăКЧНăsКПОstăЩОrПШr-
ЦКЧМО. Attempting a cut with a dull and /or dirty blade
may cause kickback and result in a serious personal
ТЧУurв.
CAUTION: ůХаКвsăЛОăsurОătСКtătСОătШШХăТsă
sаТtМСОНăШППăКЧНătСОăЛКttОrвăМКrtrТНРОăТsărОЦШЯОНă
ЛОПШrОăКttОЦЩtТЧРătШăЩОrПШrЦăТЧsЩОМtТШЧăШră
ЦКТЧtОЧКЧМО.
NOTICE: ІОЯОrăusОăРКsШХТЧОĽăЛОЧгТЧОĽătСТЧЧОrĽă
КХМШСШХăШrătСОăХТФО.ăDТsМШХШrКtТШЧĽăНОПШrЦКtТШЧăШră
МrКМФsăЦКвărОsuХt.
ůНУustТЧРătСОăМuttТЧРăКЧРХО
TСТsătШШlăТsăМКrОПullвăКНУustОНăКЧНăКlТРЧОНăКtătСОăПКМtШrвĽă
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
1. Push the carriage toward the guide fence and
tighten two clamp screws to secure the carriage.
2. Rotate the turn base until the pointer indicates 0°
on the miter scale.
22 ENGLISH
3. Rotate the turn base slightly clockwise and coun-
terclockwise to seat the turn base in the 0° miter notch.
(Leave as it is if the pointer does not indicate 0°.)
4. Loosen the hex socket bolt securing the guide
fence using the hex wrench.
►Fig.53: 1. Guide fence
5. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
AНУustătСОăРuТНОăПОЧМОăuЧtТlăТtăЦКФОsăКăЩОrЩОЧНТМ-
6.ă
ular angle with the blade using a triangular rule, try-
square, etc. Then securely tighten the hex socket bolt
on the guide fence in order starting from the right side.
►Fig.54: 1. Triangular rule
7. Make sure that the pointer indicates 0° on the
miter scale. If the pointer does not indicate 0°, loosen
tСОăsМrОаăаСТМСăsОМurОsătСОăЩШТЧtОrăКЧНăКНУustătСОă
pointer so that it indicates 0°.
►Fig.55: 1. Screw
2. Miter scale
Bevel angle
0° bevel angle
►Fig.56: 1. Lever
2. Arm holder
ЛОЯОlăКЧРlОăКНУustТЧРăЛШltă ă Ő.ăArЦă ă ő.ăRОlОКsОă
button
1. Push the carriage toward the guide fence and
tighten two clamp screws to secure the carriage.
2. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
3. Loosen the lever at the rear of the tool.
TurЧătСОăŃ°ăЛОЯОlăКЧРlОăКНУustТЧРăЛШltăĚlШаОrăЛШltěă
4.ă
on the right side of the arm two or three revolutions
counterclockwise to tilt the blade to the right.
TurЧătСОăŃ°ăЛОЯОlăКЧРlОăКНУustТЧРăЛШltăМlШМФаТsОă
5.ă
carefully until the side of the blade makes a perpendic-
ular angle with the top surface of the turn base. Use the
triangular rule, try-square, etc. as a guide. Then tighten
the lever securely.
►Fig.57: 1. Triangular rule
surface of turn table
6. Make sure that the pointer on the arm indicates 0°
on the bevel scale. If it does not indicate 0°, loosen the
sМrОаăаСТМСăsОМurОsătСОăЩШТЧtОrăКЧНăКНУustătСОăЩШТЧtОră
so that it indicates 0°.
►Fig.58: 1. Bevel scale
45° bevel angle
►Fig.59: ń.ăLОПtăŐő°ăЛОЯОlăКЧРlОăКНУustТЧРăЛШlt
AНУustătСОăŐő°ăЛОЯОlăКЧРlОăШЧlвăКПtОrăЩОrПШrЦТЧРăŃ°ă
ЛОЯОlăКЧРlОăКНУustЦОЧt.
1. Loosen the lever and tilt the blade to the left fully.
2. Make sure that the pointer on the arm indicates
45° on the bevel scale. If the pointer does not indicate
Őő°ĽăturЧătСОăŐő°ăЛОЯОlăКЧРlОăКНУustТЧРăЛШltăĚuЩЩОrăЛШltěă
on the right side of the arm until the pointer indicates
45°.
2. Hex socket bolt
3. Pointer
3. 0° degree
2. Saw blade 3. Top
2. Pointer 3. Screw