Makita DLS714 Betriebsanleitung Seite 21

Table (B)
– Molding
position in
tСОăiРurО
For inside (a)
corner
(b)
For outside (c)
corner
(d)
Example:
In the case of cutting 52/38° type crown molding for
ЩШsТtТШЧăĚКěăТЧătСОăКЛШЯОăiРurОŚ
• Tilt and secure bevel angle setting to 33.9° LEFT.
•ă AНУustăКЧНăsОМurОăЦТtОrăКЧРlОăsОttТЧРătШă3ń.6°ă
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on the
saw.
•ă TСОăiЧТsСОНăЩТОМОătШăЛОăusОНăаТllăКlаКвsăЛОăШЧă
the LEFT side of the blade after the cut has been
made.
АШШНăПКМТЧР
АůRІIІżŚ UsОăsМrОаsătШăКttКМСătСОăаШШНă
ПКМТЧРătШătСОăРuТНОăПОЧМО.ăTСОăsМrОаsăsСШuХНăЛОă
ТЧstКХХОНăsШătСКtătСОăsМrОаăСОКНsăКrОăЛОХШаătСОă
surПКМОăШПătСОăаШШНăПКМТЧРăsШătСКtătСОвăаТХХăЧШtă
ТЧtОrПОrОăаТtСătСОăЩШsТtТШЧТЧРăШПătСОăЦКtОrТКХăЛОТЧРă
Мut. Misalignment of the material being cut can case
unexpected movement during the cutting operation
which may result in a loss of control and serious
ЩОrsШЧКlăТЧУurв.
CAUTION: UsОătСОăstrКТРСtăаШШНăШПăОЯОЧătСТМФ-
ЧОssăКsătСОăаШШНăПКМТЧР.
Use of wood facing helps to assure splinter-free cuts
in workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence.
SООătСОăiРurОăМШЧМОrЧТЧРătСОăНТЦОЧsТШЧsăПШrăКăsuР-
gested wood facing.
ŻТЧТsСОНă
Molding
ЩТОМО
edge against
РuТНОăПОЧМО
Ceiling Finished
contact edge piece will be
should be on the Left
against guide side of blade.
fence.
Wall contact
edge should
Finished
be against
piece will be
guide fence.
on the Right
Ceiling side of blade.
contact edge
should be
against guide
fence.
15mm (5/8")
420mm (16-1/2")
35mm
(1-3/8")
92mm 100mm
1
(3-5/8") (3-15/16")
1. Holes
NOTICE: АСОЧătСОăаШШНăПКМТЧРăТsăКttКМСОНĽăНШă
ЧШtăturЧătСОăturЧăЛКsОăаТtСătСОăСКЧНХОăХШаОrОН.
The blade and/or the wood facing will be damaged.
űuttТЧРărОЩОtТtТЯОăХОЧРtСs
When cutting several pieces of stock to the same
length, ranging from 220 mm to 385 mm, use the set
plate (optional accessory). Install the set plate on the
СШlНОrăĚШЩtТШЧКlăКММОssШrвěăКsăsСШаЧăТЧătСОăiРurО.
►Fig.50: 1. Set plate
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and
аСТlОăСШlНТЧРătСОăаШrФЩТОМОĽăЦШЯОătСОăsОtăЩlКtОălusСă
against the end of the workpiece. Then secure the set
plate with the screw.
When the set plate is not used, loosen the screw and
turn the set plate out of the way.
NOTE: Use of the holder-rod assembly (optional
accessory) allows cutting repetitive lengths up to
2,200 mm approximately.
żrШШЯОăМuttТЧР
АůRІIІżŚ DШăЧШtăКttОЦЩtătШăЩОrПШrЦătСТsătвЩОă
ШПăМutăЛвăusТЧРăКăаТНОrătвЩОăЛХКНОăШrăНКНШăЛХКНО.
Attempting to make a groove cut with a wider blade or
dado blade could lead to unexpected cutting results
and kickback which may result in serious personal
ТЧУurв.
АůRІIІżŚ ŰОăsurОătШărОturЧătСОăstШЩЩОrăКrЦă
tШătСОăШrТРТЧКХăЩШsТtТШЧăаСОЧăЩОrПШrЦТЧРăШtСОră
tСКЧăРrШШЯОăМuttТЧР. Attempting to make cuts with
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
rОsultăТЧăsОrТШusăЩОrsШЧКlăТЧУurв.
For a dado type cut, perform as follows:
AНУustătСОălШаОrălТЦТtăЩШsТtТШЧăШПătСОăЛlКНОăusТЧРă
1.ă
tСОăКНУustТЧРăsМrОаăКЧНătСОăstШЩЩОrăКrЦătШălТЦТtătСОăМut-
ting depth of the blade. Refer to "Stopper arm" section
described on previously.
AПtОrăКНУustТЧРătСОălШаОrălТЦТtăЩШsТtТШЧăШПătСОăЛlКНОĽă
2.ă
cut parallel grooves across the width of the workpiece
using a slide (push) cut.
►Fig.51: 1. Cut grooves with blade
50mm-60mm
(2"-2-3/8")
27mm (1-1/16")
1
70mm 85mm
(2-3/4") (3-3/8")
2. Holder 3. Screw
ENGLISH 21