Gastroback Design Espresso Slim Bedienungsanleitung Seite 51

Problem Possible Reason
Not enough milk The milk is not fresh and/or
texture. not cold enough.
You need to improve your
texturing procedure.
You stopped texturing pre-
maturely.
Not enough steam is given
off.
Different brands and types
of milk and milk alternatives
will texture differently.
The milk has a The milk is not fresh and/or
stale taste. not cold enough.
The steam wand is not
clean.
With the drip tray The red float (filling level
full, the filling level indicator) sticks to the sup-
indicator does not port.
come up.
All buttons are While switching on the
flashing. appliance, the hot water/
steam switch has been in
horizontal operating posi-
tion.
You attempted to use the
hot water/steam function,
before the water system
reached brewing tempe-
rature.
You attempted to use the
hot water/steam function,
while a brewing cycle is
running.
100
The Solution
Use refrigerated and really fresh milk for texturing (see:
'Tips for Texturing Milk').
Proceed according to the instructions in the sections 'Tex-
turing Milk' and 'Tips for Texturing Milk'. Check whether
you get better results, when working with or without the
stainless steel sleeve.
The texturing process needs some time. Leave the appliance
operate until the desired quantity of froth is produced.
The steam wand could be blocked. Leave the steam wand
cool down and clean the steam wand (see: 'Cleaning the
Steam Wand').
You may need to adapt the texturing procedure. Give it a
try (see: 'Texturing Milk').
Use refrigerated and really fresh milk for texturing (see:
'Texturing Milk').
Clean the steam wand thoroughly (see: 'Cleaning the
Steam Wand').
Pull the filling level indicator upwards and out. Then turn
the a little and push it onto the support again. When
installed in correct orientation, the filling level indicator can
move freely up and down.
The hot water function is available only when the water
system reached the brewing temperature (power button
is illuminated continuously). Turn the hot water/steam
switch back to the vertical position and wait until the
power button will not flash any longer.
The functions of the appliance are available only, when
the water system reached operating temperature (power
button is illuminated continuously). Turn the hot water/
steam switch back to the vertical position and wait until
the power button will not flash any longer.
During brewing, the hot water/steam function is not
available. Turn the hot water/steam switch back to the
vertical position.
Problem Possible Reason
A severe problem occurred.
The buttons of You attempted to use the
the brewing func- hot water/steam function,
tions (1 cup and while a brewing cycle is
2 cups) and the running.
steam button are
flashing.
The buttons of the Not enough water in the
brewing functions water tank. The WATER
(1 cup and 2 LOW indicator is illuminated.
cups) are flashing
After using the steam func-
for some seconds
tion, the appliance must be
but nothing else
cooled down manually for
happens.
brewing.
Not enough water in the
water tank. The WATER
LOW indicator is illuminated.
The power button The overheat protection
and steam button has been triggered during a
are illuminated, brewing cycle.
the 1 cup and 2
cups buttons are
A technical problem occur-
flashing.
red.
The machine is Possibly, the overheat
switched on but protection of the pump is
ceases to operate active.
or steam escapes
from the group
head.
You have operated the hot
water/steam function for
more than 3 minutes.
The Solution
Immediately unplug the appliance and get in contact with an
authorized service centre for examination and repair.
During brewing, the hot water/steam function is not
available. Turn the hot water/steam switch back to the
vertical position.
Pour at least 250 ml cold water into the water tank. Then
try again.
This is normal. The temperature necessary for steam pro-
duction is too high for brewing. Proceed as described in
section 'Cooling Down to Brewing Temperature'.
Pour at least 250ml cold drinking water into the water
tank. Then try again.
The machine will return to normal operation automatical-
ly, as soon as the water system cooled down sufficiently.
Simply wait. The appliance is not intended for continuous
operation. Make a break in time.
If the machine does not recover automatically within 10
minutes, switch off the appliance (press the power button)
and wait for approx. 30 minutes. Then try again.
If the problem persists, get in contact with an authorized
service centre.
Switch off the machine and unplug. Wait for 15-30
minutes. Then try again.
This is normal. Turn the hot water/steam switch back
to the vertical position and wait until the water system
reaches operating temperature again (power button is illu-
minated continuously). If required, try again.
101