Manufacturer's Terms Of Warranty; Installation Instructions; Intended Use; Minimum Installation Dimensions - Truma Mover S Gebrauchsanweisung

Manufacturer's terms of warranty

1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults. In
addition to this, the statutory warranty claims against the seller
remain valid.
A claim under warranty shall not pertain:
– for parts subject to wear and in cases of natural wear and
tear
– as a result of not original Truma parts being used in the
appliance
– as a consequence of failure to respect the manufacturers
instructions for installation and use
– as a consequence of improper handling
– as a consequence of improper transport packing.
2. Scope of warranty
The warranty is valid for malfunctions as stated under item 1,
which occur within 24 months after conclusion of the purchase
agreement between the seller and the final consumer. The ma-
nufacturers will make good such defects by subsequent fulfil-
ment, i.e. at their discretion either by repair or replacement. In
the event of manufacturers providing service under warranty,
the term of the warranty shall not re commence anew with re-
gard to the repaired or replaced parts; rather, the old warranty
period shall continue to run. More extensive claims, in particu-
lar claims for compensatory damages by purchasers or third
parties, shall be excluded. This does not affect the rules of the
product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out by
an authorised Truma Dealer.
Additional costs based on complicated removal and installation
conditions of the appliance (e.g. removal of furniture or parts
of the vehicle body) do not come under warranty.
Rollers carry 24 months warranty against manufacturing de-
fects. Take care to remove sharp stones from your tyres prior
to using your Mover.
3. Raising the case of warranty
In the event of faults, in principle the Truma Service Centre is
to be notified: Truma Gerätetechnik GmbH & Co. KG, Wernher-
von-Braun-Straße 12, 85640 Putzbrunn. In other countries,
respective service partners are available (refer to address list).
Complaints must be specified. In addition, the correctly com-
pleted warranty certificate must be presented or the Serial
number of the appliance and the date of purchase specified.
In order to allow the manufacturer to check whether it is a war-
ranty case, the end consumer must take or send the device to
the manufacturer at his own risk.
In instances of the device being sent to the works, dispatch
is to be effected by freight transport. In cases under warranty,
the works shall bear the transport costs or the costs of delivery
and return. If the damage is deemed not to be a warranty case,
the manufacturer shall notify the customer and shall specify re-
pair costs which shall not be borne by the manufacturer; in this
case, the customer shall also bear the shipping costs.

Installation instructions

Read the installation instructions prior to starting work and
follow them carefully!

Intended use

The Mover S has been built for use with single-axis caravans
with a gross weight of up to 1800 kg.
The Mover S weighs approx. 35 kg with the cross actua-
tion device attached.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma Mover S has design approval, and a general operat-
ing permit (ABE) has been issued for Germany. Acceptance by
a vehicle expert is not required (except when installing the flat
frame kit). The ABE must be kept in the vehicle.
The Mover S complies with the vehicle engine interference sup-
pression directive 72/245/EEC with supplements 2004/104/EC
and 2005/83/EC and bears type approval number:
e1 03 4473.
The Mover S complies with EMC directive 89/336/EEC.
The remote hand set and the receiver comply with the require-
ments of the R&TTE directive 1995/5/EC.
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover is being installed.
Any modification to the unit, or the use of spare parts and
functionally-important accessories which are not original
Truma components, or failure to respect the installation and
operating instructions, will lead to the cancellation of the guar-
antee and to exclusion of claims for liability. in addition to this,
the operational approval for the device will be cancelled.
Tools and facilities required
To install the unit you will need:
13 mm, 17 mm, 10 mm socket wrench, ring spanner or
open-jawed spanner
Torque wrench (20 – 40 Nm)
Cable cutter/Crimping tool
Power drill/screwdrivers/25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting.

Minimum installation dimensions

The equipment can only be fitted to caravans/trailers within the
following dimensions.
Caravan floor
opt. 185
min. 30
max. 48
min. 60
max. 2400
all dimensions in mm
* With fully loaded vehicle
•
max. 1860
15