Charging The Battery; Cleaning - Dräger X-am 8000 Gebrauchsanweisung

12. If necessary, press
this case, a calibration happens immediately.
 The new measured value is displayed for confirmation.
The result is displayed as follows:
single-gas calibration successful.
single-gas calibration failed.
13. The single-gas calibration is complete when measuring
channel successfully passed or failed the single-gas
calibration.
● Select and then confirm the dialog to discard the
result.
● Select to confirm the result.
14. Close the valves on the test gas cylinder.
If there was an error during the single-gas calibration:
– Repeat the single-gas calibration.
– Inspect the sealing contours and surfaces on the
calibration adapter as well as the front cradle of the
housing to make sure they are free of damage. Inspect the
thread port for the calibration adapter.
– If necessary, replace the sensor.
For mixed gas and cross calibration, see the technical
manual.
5.6

Charging the battery

WARNING
Risk of explosion!
To reduce the risk of ignition of a flammable or explosive
atmosphere, observe the following:
► Do not open the gas detector in explosion-hazard areas.
► Only use the LBT 02** (lithium-ion) battery type.
► Do not charge or exchange the battery in explosion-
hazard areas.
► Only use the battery charger specified by Dräger. The use
of a different charger nullifies the explosion protection
certification of the gas detector.
For the replacement of the battery, see the technical
manual.
The battery is a part of the lower part of the casing. The
battery can be charged with or without the gas detector.
1. Place the gas detector or only the lower part of the casing
with the battery in the charging cradle.
 The gas detector switches off automatically (factory
setting). The green LED on the power pack flashes.
The typical charging time after a work shift of 8 – 10 h is
approx. 4 h.
The typical charging time for an empty battery is approx. 10 h
If the battery is deep-discharged, it may be necessary to
leave the device in the charging cradle for up to 16 h to
charge it.
Instructions for use |
X-am
to overrule the stability control. In
®
8000
If the specified temperature range (5 to 35 °C) is not reached
or is exceeded, charging stops automatically. This extends the
charging time. After a return to the temperature range,
charging continues automatically.
WARNING
No measurement!
If there is an external power supply voltage drop > 1 s in the
charging cradle while the gas detector is in operation, the gas
detector switches off.
► Ensure uninterrupted power supply (does not apply if the
optional setting, that the gas detector does not
automatically turn off in the charging cradle, is selected). If
this cannot be ensured, regularly check that the gas
detector is turned on (e.g. based on the optical and
acoustic operating signals).
Designation and descrip-
tion
Inductive charging cradle for
charging 1 gas detector
Adapter for the plug-in power
supply unit
Plug-in power supply unit for
charging 1 gas detector
Plug-in power supply unit for
charging 5 gas detectors
Plug-in power supply unit
100-240 V AC; 1.33 A for
charging up to 5 gas detec-
tors
(requires adapter 83 25 736)
Plug-in power supply unit
100-240 V AC; 6.25 A for
charging up to 20 gas detec-
tors
(requires adapter 83 25 736)
Vehicle connection
12 V / 24 V for charging
1 gas detector
Vehicle connection 12 V / 24
V for charging up to 5 gas
detectors
(requires adapter 83 25 736)
Vehicle mount
(requires adapter 83 25 736
and vehicle connection cable
83 21 855)
5.7

Cleaning

The gas detector does not require any special care.
If it is heavily soiled, wash the gas detector with cold water
and use a sponge if necessary. Use a cloth to dry the gas
detector.
|
Maintenance en
Order no.
83 25 825
83 25 736
83 16 997
83 16 994
83 21 849
83 21 850
45 30 057
83 21 855
83 27 636
49